Reservoir D is fed by a pump and pipe system. Pressure heads in the pipe flow at the entrance and at the outlet from the pump are 5 m and 105 m, respectively. The geometric of the pipe before the pump is 0.50 m. The efficient power of the pump is 75 kW. The friction factor at all the pipe system is f = 0.03. Minor losses are to be neglected.

Reservoir D is fed by a pump and pipe system. Pressure heads in the pipe flow at the entrance and at the outlet from the pump are 5 m and 105 m, respectively. The geometric of the pipe before the pump is 0.50 m. The efficient power of the pump is 75 kW. The friction factor at all the pipe system is f = 0.03. Minor losses are to be neglected.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation XX: In the figure shown, z, = 4 m, length of pipe from the reservoir to the pump is 120 %3D m, from the pump to the nozzle is 1000 m. The diameters of pipes are 0.60 and 0.45 m respectively. The gage pressure at B (the suction side of the pump) is -64 KPa. Neglect minor losses. В C P. 0.45 m diam. LCD = 1000 m %3D Zp = 4 m f = 0.02 0.60 m diam. LAB = 120 m f = 0.02 %3D 52. Compute the velocity of water in pipe AB. a. 2.297 m/s b. 1.452 m/s c. 3.147 m/s d. 2.672 m/s 53. Compute the velocity of water in pipe CD. a. 1.23 m/s b. 4.08 m/s c. 3.56 m/s d. 5.59 m/s 54. Compute the discharge of the pipe from A to B due to pumping. a. 0.65 m3/s b. 0.45 m3/s c. 0.89 m³/s d. 0.25 m3/s 60 m, f= 0.02 m and loss of head ith
Question 3) Water transmission line is constructed to transmit water from A reservoir to city with 200 l/s of total discharge. 150 l's is supplied from reservoir and the other part is added from B point (Use same types of pipes through the pipeline). Maximum allowable pressure on the pipeline is 100 m. Minimum pressure of transmission line, (–), = 3 m, William-Hazen coefficient, C is 100. (V = 0.85CR0 Josa ). Determine the diameter of pipeline, design WTL economically. Commercial Pipe Diameters: $200,250, 300,350, 400, 450, 500, 550, 600. 250m 162m (A) (3) 100m 50 V's/ (B) 1000 m 2000 m City 3000 m
The difference in the water surface of the two reservoirs is 9m. The reservoirs are connected by a siphon of length 1000m and 0.2m diameter. The summit of the pipe is 3m above the water surface level of upper reservoir. The length of pipe from upper reservoir to the summit is 200m. Determine the discharge through the siphon and also the pressure at the summit. Take friction factor as 0.02 and neglect all minor losses.
The pressure gauges are inserted at A and B in a vertical pipe converging water. The diameters at A and B are 150mm and 75mm respectively. The point B is 2.3m below point A. When rate of flow down the pipe is 0.021m³/s. The pressure at B is 117.72 KN/m² greater than at A. The losses in pipe between A and B are expressed as(KVa²/2g) where Va is velocity of A. Find the value of K. If the pressure gauges at A and B are replaced by tubes filled with water and connectef to a u-tube containing Hg(SHg=13.6) calculate the value of the reading manometer.
Problem-3: A centrifugal pump lifts water against a static head Az = VEN m. The pipe setup has a constant diameter of 0.08 m, major losses in the suction side h,, = EN m and in the discharge side hip is 3 m. The pump impeller has a diameter of 0.15 m, exit width of0.015 m, exit blade angle of 22° and speed ofN=20EN rpm The hydraulic efficiency is 0.85. If the flow at the entrance is radial, find the discharge, pump head, atmospheric pressure Pa. vapor pressure P, and maximum allowable height of the pump from the feeding tank water surface elevation if the pump is operating under T= 25 °C at altitude H= 20EN m. %3! o, = NPSH, IH, =1.21x10 N - P,)/y-hST-H, !3! !! SM (P al-abs $256 Par ly =10.33(1–2.256x10-H (14 29-3985:(T+2334) !!
pl 3. A syphon of diameter 200 mm connects two reservoir having a difference in elevation of 20 m. Total length of syphon is 500 m and summit is 3.0 m above the water level in upper reservoir. Coefficient of friction = 0.05. If length of pipe from upper reservoir to summit is 100 m then, determine (a) Discharge through syphon. (b) Pressure at summit.
c. 56.23 N/m3 d. 60.18 N/m2 Situatton XC: In the figure shown, z,-4 m, length of pipe from the reservoir to the pump is 120 m, from the pump to the nozzle is 1000 m. The diameters of pipes are 0.60 and 0.45 m respectively. The gage pressure at B (the suction side of the pump) is -64 KPa. Neglect minor losses. D. B. 0.45 m diam. LcD=1000 m f%=0.02 %3D Zp = 4 m 0.60 m diam. LAB= 120 m f%30.02 52. Compute the velocity of water in pipe AB. a. 2.297 m/s b. 1.452 m/s c. 3.147 m/s d. 2.672 m/s 53. Compute the velocity of water in pipe CD. a. 1.23 m/s b. 4.08 m/s C. 3.56 m/s d. 5.59 m/s 54. Compute the discharge of the pipe from A to B due to pumping. a. 0.65 m/s b. 0.45 m2/s c. 0.89 m/s d. 0.25 m /s 60m. -0.02 m and loss of head
A 300 mm cast-iron pipe is discharge 120 lit/sec. At a point 200 m from the reservoir the center of the pipe is 30 m below the reservoir surface. What is the pressure in kPa to be exerted there? Assume f= 0.02
A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
An 8 hp pump is installed near the reservoir containing oil having a sp. gr. of 0.82. The rate of flow of the pipe is 0.014 m/s. The pressure heads at 1 and 2 are -28 kPa and 290 kPa respectively. Compute the output in hp by the pump. 290 kPa 50mm o 0.90m -28 kPa 50mm o 8hp pump Oil (0.82)
Water is pumped from reservoir A at elevation 250 m. The pump is close to reservoir A and is at the same elevation as reservoir A. It is pumping 90 liters per second of water through a 1,000 m of 150 mm diameter pipe to a reservoir whose elevation is 300 m. What is the pressure at a point where the elevation is 280 m and at a distance of 750 m from the pump? Assume f=0.02 and neglect minor losses. Select one: O a. 325.15 kPa O b. 615.38 kPa O c. 512.54 kPa O d. 912.60 kPa
What is pipe roughness? A pump is located 5 m above the surface = 8170 M/m¹) in a closed tank. The pressure in the space above liquid surface is 35 Kpa. The suction line to the pump is 15 m of 15 cm diameter pipe (/= 0.025). The discharge from the pump is 60 m of 20 cm diameter pipe (/= 0.03). The pipe discharges in a submerged fashion to an open tank whose free liquid surface is 3 m lower than the liquid surface in the pressure tank. If pump puts 1.5 kW Into the liquid, determine the flow rate and the pressure in the pipe on the suction side of the pump. Assume turbulent flow.