Required information Two solid cylindrical rods AB and BC are welded together at 8 and loaded as shown. Take di = 30 mm, d₂ = 50 mm, and P = 85 KN. 0.9 m 125 AN 125 IN 12 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is | MPa.

Required information Two solid cylindrical rods AB and BC are welded together at 8 and loaded as shown. Take di = 30 mm, d₂ = 50 mm, and P = 85 KN. 0.9 m 125 AN 125 IN 12 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is | MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Similar questions

Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
gure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30kN. If Young's odulus for the alloy is 69GPA determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 P Figure 1
ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30KN. If Young's odulus for the alloy is 69GPa determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3
ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30KN. If Young's odulus for the alloy is 69GPa determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 Figure 1
Required information Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. Given: P₁ = 65 kN and P2 = 40 kN. Take Es = 200 GPa and Eb = 105 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -180- Dimensions in mum Steel B 120- P₁ 40-mm diam. 100 100 DI C Brass 30-mm diam. Determine the reactions at A and E. The reaction at A is The reaction at Eis P2 E KN (Click to select) ✓ KN (Click to select)
each sold bar has a 36N/m weigh If the 1:In the following arrangement of structur allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. 36N/M 2m im Im 2m
find the tensile of the bolt with diameter 38mm,80kN
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W