Required information A torque T-130 N-m is applied to the shaft EFG, which is running at constant speed and contains gear F. Gear F transmits torque to shaft ABCD through gear C, which drives the chain sprocket at B, transmitting a force Pas shown. Sprocket B. gear C. and gear F have pitch diameters of a-120 mm, b=200.004 mm, and c= 100 mm, respectively. The contact force between the gears is transmitted through the pressure angle = 20⁰. 25 4-30mm f-250

Required information A torque T-130 N-m is applied to the shaft EFG, which is running at constant speed and contains gear F. Gear F transmits torque to shaft ABCD through gear C, which drives the chain sprocket at B, transmitting a force Pas shown. Sprocket B. gear C. and gear F have pitch diameters of a-120 mm, b=200.004 mm, and c= 100 mm, respectively. The contact force between the gears is transmitted through the pressure angle = 20⁰. 25 4-30mm f-250

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc = 392 lb-ft is removed from the shaft at gear C, and the remaining torque is removed at gear D. Assume that DA-4-in.-diameter, Dg=12-in.-diameter, L₁=56 in., and L₂-30 in. Segments (1) and (2) are solid 1.5-in.-diameter steel [G = 12200 ksi] shafts, and the bearings shown allow free rotation of the shaft. Determine: (a) the maximum shear stresses T₁, T₂ in segments (1) and (2) of the shaft. (b) the rotation angle D/B of gear D relative to gear B. Answers: (a) T₁ (b) D/B = = i ᎠᏴ ; A DA i B L₁ Tc amala ksi, T₂ = L2 i Tp D ksi.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 400 The shaft is mounted on two 400 400 270 250 ]640 210 640 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 100
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh. The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at each pair assuming equal direction of load between the pairs. Neglect friction.
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
A spur gear transmits 35 N · m of torque to the 20-mm-diameter driveshaft. The 5-mm-diameter setscrew threads onto the gear’s hub, and it is received in a small hole that is machined in the shaft. What's the factor of safety aganist yield under shear loading
Assignent no 1 Qt+ A Compound gear 6 Jears. No of teeth; train Consists of A B D 60 40 35 २४ 50 30 shaft on another shaft. The Gears B ş C are on one while are gears Gear A drives c drives gear D B, gear gear S gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2+ State advatages of Cycloidal In volute profile as a gear tooth pnfile.
Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c . use G=80 Gpa 280 N.m A 150 N.m B 40 N.m
1. A 9/16 inch height x 3.5 inches length flat key is keyed to a 50.8 mm diameter shaft. Determine the torque developed in key if bearing stress allowable is 35 Ksi. Use factor of safety of 3.
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angleare in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh.The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at eachpair assuming equal direction of load between the pairs. Neglect friction.