Read the question carefully and give me all right solutions. If you don't know the solution please leave it but don't give me wrong solution. If the initial dissolved oxygen of a 3 mL sample is 7.5 mg/L and after day 5 is 5.5 mg/L, with a k rate determined to be 2 mg/L. what is the BOD5 ? Ultimate BOD ? BOD 2 ? BOD 10? . Create a BOD graph (time vs BOD) .

Read the question carefully and give me all right solutions. If you don't know the solution please leave it but don't give me wrong solution. If the initial dissolved oxygen of a 3 mL sample is 7.5 mg/L and after day 5 is 5.5 mg/L, with a k rate determined to be 2 mg/L. what is the BOD5 ? Ultimate BOD ? BOD 2 ? BOD 10? . Create a BOD graph (time vs BOD) .

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter10: Oxidation, Degradation, Corrosion, Electroprocessing, Batteries, And Fuel Cells

Section: Chapter Questions

Problem 10.1P

See similar textbooks

Similar questions

3. Table below shows the concentration of dissolve oxygen for a BOD test, diluted by 100. Time (days) Diluted sample DO (mg/L) 7.95 1 3.75 2 3.45 2.75 2.15 1.8 i. Determine BOD5 Given the deoxygenation rate coefficient of 0.15 day-1, determine the ultimate BOD ii. iii. Based on answer from (i), identify class of the water sample based on INWQS guideline and propose suitable usage the water.
If a sample of tap water contains 400 ppm of Ca2+ and 80 ppm of Mg2+, what is the hardness of this water sample in terms of equivalent concentration CaCO3, in mg/L? a.80 ppm CaCO3 b. 400 ppm CaCO3 c. None
A sample of gas occupies 3.75 L at 1.15 atm and 25 °C. At what temperature will it occupy 4.00 L at 1.00 atm? Initial: Final: Effect:
JQuestion a) Write down the chemical equations for the reactions that take place in the DO test. b) Discuss the environmental significance of DO. c) Why should DO fixation be performed in the field rather than in the laboratory? Data Sheet Volume of solution for titration = Samples Sample A Sample B (i) (ii) (iii) (i) (ii) (iii) Average Average Titration reading Start End (+0.05mL) (+0.05mL) mL Volume of Na2S2O3 (mL) Dissolved Oxygen (DO)(mg/L)
Calculate the THOD of a 300 mg/L solution of C5H8O2N.
You made an error and changed the concentration of your NaOH from 0.100M to 1.00M for the potentiometric titration of acetic acid. Beyond this, you followed the rest of the procedure properly. Your acetic acid's buffer capacity will (increase, decrease, not be affected) because
The efficiency for a steel specimen immersed in a phosphating tank is the weight of the phosphate coating divided by the metal loss (both in mg/ft2). An article gave the accompanying data on tank temperature (x) and efficiency ratio (y). Temp. 171 Ratio 0.78 1.29 1.34 y = 173 174 Ratio Temp. 181 Ratio 1.47 1.62 1.63 2.09 181 181 Temp. 183 183 183 175 1.83 1.98 2.78 1.13 181 185 175 1.17 181 2.21 185 176 1.14 182 0.86 186 177 1.02 182 1.45 187 178 1.82 183 0.82 189 1.59 2.42 3.10 1.97 3.00 (a) Determine the equation of the estimated regression line. (Round all numerical values to four decimal places.) (b) Calculate a point estimate for true average efficiency ratio when tank temperature is 183. (Round your answer to four decimal places.) (c) Calculate the values of the residuals from the least squares line for the four observations for which temperature is 183. (Round your answers to two decimal places.) (183, 0.82) (183, 1.83) (183, 1.98) (183, 2.78) Why do they not all have the same…
Iron pyrite is often called “fool's gold” because it looks like gold (see page 11). Suppose you have a solid that looks like gold, but you believe it to be fool's gold. The sample has a mass of 23.5 g. When the sample is lowered into the water in a graduated cylinder (Study Question 63), the water level rises from 47.5 mL to 52.2 mL. Is the sample fool's gold (d = 5.00 g/cm3) or “real” gold (d = 19.3 g/cm3)?
Two milliliters of 0.025molars potassium iodate solution was used to standardized the sodium thiosulfate used in dissolved oxygen (DO) determination. If 19.4mL of the sodium thiosulfate solution was used, what is the corrected established relationship? (pre-established relationship: 10mL sodium thiosulfate = 1 ppm DO) 10mL Na2S203 solution = 0.104 mg/L DO 10mL Na2S203 solution = 1.856 mg/L DO 10mL Na2S203 solution = 0.224 mg/L DO O 10mL Na2S203 solution = 1.232 mg/L DO
The nutural frequancy for the system is equal to k rigid uniform bar of mass (m) P b L 1 3kb2+PL 1 3kb2 mL? 2n The answer is O The Answer is 3kb²–3PL 2n V None of All mL? The Answer is O the answer is 3kb2+3PL mL? 1 the Answer is
6 Ydu will obtain 2.0 L of tap water for you water hardness test. The water hardness test uses a precipitation reaction to precipitate the Calcium bicarbonate present out of solution by adding 1.9 g of Ca(OH) represented by the following equation: Ca(HC03|21ag) + Ca(OH)215) > 2CaCOsisi + 2 H20 ml What is the percent yield of CaCO3 produced in the hard water test? (fig. 4)
A water sample contains the following dissolved ions: [Na+] = 75 mg/l [HCO]=250 mg/1 [CH] = 100 mg/l [Ca²+] = 45 mg/l [Mg²+] = 48 mg/1 [A1³+] = 5 mg/1 Atomic weight: H = 1; C = 12; O=16; Na = 23, Ca = 40, Mg = 24; Al = 27; CI = 35.5 The total hardness of the sample in mg// as CaCO3 is