QUESTION: According to OSHA's key forklift loading requirements, when should the forks be tilted forward? The forks can be tilted forward: POSSIBLE ANSWERS: Olf carrying a load that is off-center. Olf the forklift is unattended or powered off. OWhen picking up or dropping off a load. Whenever the forklift is in use.

Q: Module 4 6. Identify the safety features shown in this automobile from the following list. Place…

A: There are several safety features in modern automobiles that reduce the risk of injury to the driver…

Q: Task 2: Is Obrass >OR < aFe bimetallic strip since the bimetallic strip curves in towards iron side…

A: Write the expression of coefficient of expansion during heating. α=Lf-LiLi1Tf-Ti

Q: Is a hook good on a compression spring launcher trigger mechanism

A: Given Spring triggered mechanism To find Verify hook is good for spring triggered mechanism

Q: 11. A rear flange mounted cylinder extends 14 in. under a load of 10,000 Ibf. What size cylinder rod…

A: Given       Mass, m = 10000 lbf                     = 4535 kg Extension, h = 14 in…

Q: a question, select your answer and click the Submit Answer button. To temporarily skip a question,…

A: Forklift Loading Requirements.

Q: What types of traction machines are used for hoisting elevators?

A: Given Data→ Traction machines Hoisting elevators

Q: A α Applied Load. 3D

A:

Q: loaded overhanging

A: ∑MB=0RA*8-10*10-6*9-20*7-20*6-15*4-15-20*3-30*1.5+15*1=0RA=72.375 kN…

Q: Define the term the radius of the pedestal?

A: The pedestal is basically a compression member used as a support for columns or other structures

Q: Which therbligs correspond to which activities? 1.Lift and move wrench toward screw 2.Reposition…

A: Solution:

Q: If 4 lengths of support brace are required for a job, 34 13" and 45 57 1", what is the total length…

A: Given Data⇒ Lengths of subparts is : L1=341316''L2=4578''L3=291516''L4=5714''

Q: QUESTION: According to OSHA's key forklift loading requirements, when should the forks be tilted…

A: Forward tilt is implied to help the administrator in pulling back the forks from a stack after…

Q: swejbeip eu Me diagrams TIS load on overhang point of contra-fle

A:

Q: Which of the following statements about supports is correct? A) all B) Bearings can be in the form…

A: Bearings do come in the form of sliding, fixed, built-in and intermediate joints. There is no…

Q: are a free-body diag rmine the support re ds without decimals

A:

Q: Identify the material handling equipment which can move in a fixed path and has a cantilever support…

A: In jib crane can move in a fixed path and has cantilever support and in bridge crane has two…

Q: Is truss stable

A: Given data : Member in truss=m Support reaction in truss=R Joint in truss=J   Required : Is truss…

Q: Select the material is used for automobile bodies. a. High Carbon Steel b. Mild Steel c. Medium…

A: Solution:

Q: The ball skidding can be reduced or eliminated by ________________________ of bearings. Static…

A: Option (c) Lubrication. Is correct Option

Q: Explain the Horizontal point load at the surface ?

A: given: Explain the Horizontal point load at the surface ?

Q: Is truss stable or not

A: Given data : Number of member=m=3 Number of joint=J=3 Number of external support reaction=R=1+2=3…

Q: Question 2: How long a wrench is needed to tighten a 9/16-inch bolt if the maximum force (pull) that…

A: Given: The diameter of bolt, d = 9/16 in = 0.5625 in The maximum force produced by mechanic, F = 75…

Q: What happens if the load on an actual column exceeds its critical loading?

A: There are two types of the column, 1. Short Column 2. Long Column The slenderness ratio and length…

Q: P.

A:

Q: Fork trucks are usually suitable for small area material handling Select one: True False

A: Given Data⇒ Fork Trucks

Q: Briefly discuss, how the energy consumptions for operations of a fork lifter could be justified.

A: On average, one forklift consumed 65 L of diesel fuel per day, 7 L per hour, 1.6 L per load, 0.7 L…

Q: Explain features of fork lift trucks.with a neat sketch show its parts

A: A forklift (also called lift truck, jitney, fork truck, fork hoist, and forklift truck) is a powered…

Q: If rods are used to support a precision movement such as a positioning table, the table will ride on…

A: Precision movement of the robot’s arm is the measure of the performance in any system. In robotics…

Q: Is truss stable or not

A: Introduction : The structure is truss structure in which their are 13 members connected by 8 joints…

Q: Draw diagrams (this requires some thought) that show to lift a heavy box, a beam can be used as a:…

A: Solution:

Q: for beam below what is the correct BMD 5 kN, 2 kN/m 10 m

A:

Q: What basic calculations would be made to verify the general problem statement: "lift cylinder…

A:

Q: Lap Joint Questions The following questions all use this figure. Assume a bolt will be put in each…

A: Given: To find: Number of fasteners counted  for calculating area of net cross section.

Q: Discuss Metal Benchwork

A: Benchwork is the use of basic hand tools to shape and form metal into shapes that you need. But if…

Q: EVENTS CEV Opsi, determine the maximum load Pmax that TL

A:

Q: What is the method used for specifying the allowable load for a member/

A: Allowable load is defined as the amount of load when applied on a member does not cause any failure…

Q: erence between a point loa

A: Difference between point load  and distributed load

Q: ww Slender har of mass Rigid masskesa link Thin đisk of mass no slip

A: The torque method can be applied on the disc about its point of contact. At point of contact for…

Q: Why is it necessary to restrict the applied load to one that is less than the load the member can…

A: It is necessary that in static and dynamic systems, the applied load must well below the maximum…

Q: If pressure or force has to be applied to mating components during assembly, then type of fit is…

A:

Q: Load on member DC please include fbd, proper solution, proper symbols, force direction

A:

Q: NLESS OTHERWISE SPECIFIED : MATERIAL: FORGED STEEL NAME: LATCH BOLT 9-9 OLERANCES +/-.006 FINISH:…

A: 12. Maximum dimension = 0.623 + 0.003 = 0.626  13. Minimum dimension = 0.623 - 0.003 = 0.620 10.…

Q: What is the magnitude of the load in member DG? *

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.