Question 3: The cast iron of a small press has a cross section as shown. For Q = 16-kips, determine: a- the maximum tensile and compressive stresses at section a-a. b-the amount of tensile or compressive force applied to the inner part (2"x12") of the section. Answers: a: = 2,992-psi (T) b: F =-5,650-psi (C) 51,072-lbs in tension 15 in. el A B 2 in. 8 in. C '3 in. 5 in. 2 in. 5 in. Cross Section a-a

Question 3: The cast iron of a small press has a cross section as shown. For Q = 16-kips, determine: a- the maximum tensile and compressive stresses at section a-a. b-the amount of tensile or compressive force applied to the inner part (2"x12") of the section. Answers: a: = 2,992-psi (T) b: F =-5,650-psi (C) 51,072-lbs in tension 15 in. el A B 2 in. 8 in. C '3 in. 5 in. 2 in. 5 in. Cross Section a-a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rectangular bar has a width of w = 3.00 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5.Determine(a) the magnitude of load P.(b) the shear stress on plane AB.(c) the maximum normal and shear stresses in the block at any possible orientation.
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 139°C. Determine the normal stress in the aluminum rod.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
A steel wire 5-m long hanging vertically supports a weight of 1200 N. Determine the required wire diameter if the stress is limited to 140 MPa and the total elongation must not exceed 4 mm. Neglect the weight of the wire and assume E = 200 GPa.
Determine the maximum normal stress in the bar. The diameter is 1.5cm.F1 = 7KN F2 = 6KN F3 = 2KN F1 = 9KN
A steel wire 5 m long hanging vertically supports a weight of 1200 kN. Determine the required wire diameter if the stress is limited to 140 MPa and the total elongation must not exceed 4 mm. Neglect the width of the wire and assume E=200 GPa.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
A 5-mm thick hollow steel has an allowable stress limited to 200 MPa. Determine the inside and outside diameter of the tube if the force applied is 100 kN.Answers: ro _______________ rt__________________
The tensile member shown, 50 mm x 75 mm in cross section is subjected to a load P. The plane A-A makes an angle 15° with the x-axis. a. Determine load P when the tensile stress at section A-A is 80 MPa. b. Determine the shear stress on section A-A. c. At what angle of plane A-A is the shear stress equal to 27.35 MPa?
Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. The density of brass is 8470 kg/m^3 Determine normal stresses of ((σzz)AB and (σzz)BC) as a function of z, and draw the variation of stresses with respect to z-axis on the same graph.