QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load Plocated at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm2 and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm

QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load Plocated at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm2 and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W = 150 kN is applied. A (mm?) a (FC) E (GPa) Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83 Bronze | 3 m Steel 1.5 m ►| 1.0 m 2.5 m 2 m W
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
A The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 3 mm; and (ii) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of Problem 4: Steel A= 480 mm? 1.0 m B elasticity are 200 GPa for steel and 80 GPa for bronze. Problem 5: The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for alumi- num, and the total elongation of the bar is not to exoceed 0.2 in. 3P Bronze A= 650 mm 2 m 3 ft 4 ft 2P Steel A = 0,4 in.2 E = 29 × 10° psi 2P Aluminum A = 0.6 in.2 E= 10 x 10° psi
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².