fluid mechanicsquestion is image3.a only a ? Question 3An engineer is trying to measure the localvelouty insidea bounday layer over a flat plate with a Pitot tube. The Pitottube is placed 350 mm from the leading edge, 0.7mm above the vwall.Air at STP with Loo =20 m/s flows over the flat plate, The Pitot ubeis connected to a wato mano meter which qives a readiig ef 10 mm HzDThe velouity po fileinside the B.L. is givei by:3.uly) -4 --- wheve s is the B.Lthickness.3.a) The engineer makes the necessomanometer reading (Ahel0 mm)is not corect.Carm out the sanecalculations and calkulate the "comrect" mano meter reading.calculations cnd shows that theniolut hoxeled te incorrect

Answered: Image /qna-images/answer/59fef8b1-cebd-421d-8f3b-9f3122c44e36.jpg

Question 3 An engineer is trying to measure the local velouity bounday layer over a flat plate with a Pitot tube. The "Pitet tube is placed 350 mm from the leading edge, 0.7mm above the wall. Air at STP with Loo =20 m/s flows over the flat plate, The Pitot tube a reading ef 10 mm HzO inside a is connected to a wato mano meter which gives The velouty profile inside the B.L. is givei by:

Question 3 An engineer is trying to measure the local velouity bounday layer over a flat plate with a Pitot tube. The "Pitet tube is placed 350 mm from the leading edge, 0.7mm above the wall. Air at STP with Loo =20 m/s flows over the flat plate, The Pitot tube a reading ef 10 mm HzO inside a is connected to a wato mano meter which gives The velouty profile inside the B.L. is givei by:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A small capillary with an inside diameter of 2.22 x 10-3m and a length 0.317m is being used to continuously measure the flow rate of a liquid having a density of 875 kg/m3 and viscosity of 1.13 x 103 Pa-s. The pressure drop reading across the capillary during flow is 0.0655m water (Density is 996 kg/m3). What is the flowrate in cu.fps?
92 the Pressare difference oP in a pipe of diameter (DJand length (L) due to Viscogus flow depend viscosity (h) and density (S) . obtuind évpression ofOP? on the velocity U),
For free flow of air over a plate, it is given that Grashof number is 7 x 10º and Prandtl number is 0.25 Then, determine the type of flow.
1- Consider single-phase fluid flow in a 1-D horizontal reservoir.The reservoir is discretized using four blocks in the x-direction. A well located in block 3 produces at a rate of 400STB/D. All grid blocks have Ax-250ft, w-900ft, h-100 ft, and kx-270md. The FVF and the viscosity of the flowing fluid are 1.0 RB/STB and 2cP, respectively. Identify the interior and boundary blocks in this reservoir. Write the flow equation for block 3 and give the physical meaning of each term in the equation.
9At 1 atm and 20 oC, air flows in a 7 cm diameter tube. What should be the maximum air velocity to keep the flow laminar? (kinematic viscosity 1.516E-5 m^2/s)
-drill Pipe supp-rt its an oil wel is drilled, each nerw section the we'git Own weight of the pipe and 8.00-m-long steal Pipe that supports a 200,000g dril 5A and a 5 km length the drill bit beneath it. Calculate the stréch ing new and OF pipe with a linear mass dersity of 20 kglm. Treat the pipe as a solid cylinder with a 8.00 cm diaimeter.
A long fi xed tube with a rounded nose, aligned with anoncoming fl ow, can be used to measure velocity. Measurementsare made of the pressure at (1) the front nose and(2) a hole in the side of the tube further along, where thepressure nearly equals stream pressure.( a ) Make a sketch of this device and show how the velocityis calculated. ( b ) For a particular sea-level airfl ow, the differencebetween nose pressure and side pressure is 1.5 lbf/in 2 .What is the air velocity, in mi/h?
The thrust of a shaft is taken by a collar bearing provided with a forced The lubrication system maintains a film of oil of lubrication system. orm thickness between the surface of the collar and the bearing The mal and intemal diameters of collar are 16 and 12 cms. respectively. The thickness of oil film is 0.02 ems. and coefficient of viscosity is 0.91 naise. Find the horse-power lost in overcoming friction: when the shaft is notated at a speed of 350 E.p.m. Skult
Water flows through a circular tube with a velocity of 2 m/s. The diameter of the pipe is 14 cm. If the kinematic viscosity of water is 10-6 m?is and density 1000 kg/m3, the Reynolds number of the flow can be calculated as O 2.8 x 108 2.8 x 105 280 2800
Gasoline at 20°C flows at 105 m3/h in a 10-cm-diameterpipe. We wish to meter the flow with a thin-plate orificeand a differential pressure transducer that readsbest at about 55 kPa. What is the proper β ratio for theorifice?
At a point in a pipe that lay flat ノ water in the pipe flows at a speed of 9.0 mls and has 6-40x 104 Pa a gaoge pressure is Find the gauge pressure at point 2 of pipe that lower than the first point 8.0 m and the cvoss - se ctional| area of the pipe is double of first point . Answer [1.52x105 Pa]
Air is flowing naturally over a cylinder of D=(1) cm. Air has thermal conductivity 0.027W/mK, kinematic viscosity 1.9*10-5 m2/s, Rayleigh number 108, and Prandtl number0.72. Find the Nusselt number uses charts/table also if needed