QI An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Culoss of 1.6 kW. Determine (a) the kVA load for maximum efficiency and the minmum efficiéncy (b)the efficiency at half full-load at 0.8 * power factor lagging

QI An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Culoss of 1.6 kW. Determine (a) the kVA load for maximum efficiency and the minmum efficiéncy (b)the efficiency at half full-load at 0.8 * power factor lagging

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11P: For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power...

See similar textbooks

Related questions

Q: 120/480 V, 10 kVA two-winding transformer is to be used as an auto-transformer to supply a 480 V…

Q: A 10 kVA, 2400/240 V, 60 Hz single phase transformer has Z, = 5.2 + j12.5 ohms and Z2 = 0.06 + j0.12…

A: In this question, We need to calculate the load voltage if Primary voltage and frequency is rated.…

Q: A 2,300/240-V, 60-Hz, 4.6-kVA transformer isdesigned to have an induced emf of 2.5 V/turn.Assuming…

A: The given transformer is a step-up transformer. a. The numbers of high-side turns are calculated as…

Q: A 4 MVA, 66/13.2 Kv, 50 Hz. Delta star connected Three phase transformer has a primary resistance…

A: The current flowing in a circuit causes a voltage drop. The voltage drop should be within allowable…

Q: Given a transformer (single-phase, 10kVA, 2400/240V, 60Hz) Z1 = 5.2 + j12.5 ohms; Z2 = 0.06 + j0.12…

A: In this question we need to find a load voltage of transformer for given condition.

Q: 3.57 A two-winding single-phase transformer rated 60 kVA, 240/1200 V, 60 Hz, has an efficiency of…

A: Transformer : A transformer is a stationary device that transmits electrical energy from one circuit…

Q: A transformer takes a No load current of 0.64 A and power factor of 0.654 lag, when its primary is…

A: First we will draw phasor diagram , from phasor diagram we will find relation between iron loss…

Q: Q2) A 140-kVA, 7500/277-V distribution transformer has the following resistances and reactances: R,…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Culoss…

A: In this question , transformer cu loss and iron loss given..Output KVA given..We have to find out…

Q: A 2000-kVA, 6,600/400-V, 3-phase transformer is delta-connected on the high Example voltage side and…

Q: A 10-kVA, 2000/400-V, single-phase transformer has resistances and leakage reactances as follows :…

A: The information we have : Primary voltage, V1 = 2000 V Secondary voltage, V2 = 400 V So,…

Q: (a) A 5 MVA 230/11.5-kV single-phase power transformer has a per-unit resistance of 1.5% and a…

Q: Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding…

A: The transformation ratio of the transformer is determined as:

Q: A transformer takes a No load current of 0.29 A and power factor of 0.405 lag, when its primary is…

A: Given, No load current (Io)= 0.29 A No load power factor= 0.405 lagging No load supply voltage…

Q: (a) A 5 MVA 230/10.5-kV single-phase power transformer has a per-unit resistance of 1.5% and a…

Q: Example: A single-phase, 100-kVA, 1000:100-V, 60-Hz transformer has the following test results:…

Q: A single-phase l0-kVA, 480/1120 -V transformer is to be used as an auto transformer tying a 600V…

Q: A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down…

A: As per the guidelines, the first 3 sub-parts have been solved. (a). The value of the turns ratio…

Q: A 400-k VA, 2300 230, 60-hz transformer supplies a 0.8 lagging power-factor load whose KVA Is…

A: The efficiency of the transformer is given by the relation, Where, x = percent rated load…

Q: Transformer rated powers and relative short-circuit rates in a step-down transformer station are…

A: For the electrical design of the electrical substation, Short circuit MVA and Short circuit current…

Q: (b) A 50-kVA, 2600/1300-V, single-phase transformer has a core loss of 780 W. The transformer has a…

Q: A 230-kVA, 2300/230-V, 60-Hz, step-down, two-winding transformer has the following parameters RH =…

A: Given data: S=230 kVARH=1.2 ΩRL=12 mΩXH=3 ΩXL=30 mΩRcH=2 kΩXmH=1.8 kΩVp=2300 V

Q: 8.(a) A 100 KVA, 50 Hz, 440/11000 V, 1-phase transformer has an efficiency of 98.5% when supplying…

A: Let Pi → Iron losses Pl4→Full load copper losses At full load , 0.8 Power factor efficiency=98.5…

Q: A two-winding transformer is rated at 60-kVA, 240/1200-V, 60-Hz. When operated as a conventional…

A: It s given that: KVA=60V1V2=2401200f=60 Hzcosϕ=0.8 V1V2Auto=2401200

Q: A 20-kVA 8000/480-V distribution transformer has the following resistances and reactances: R, = 32N…

Q: Problem 2. A 150-MVA, 220/22-kV, three-phase has the following parameters (in 2): R2 = 0.001 X, =…

A: In the question, All parameters are given of transformer. Determine the equivalent circuit…

Q: The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding…

Q: Rated values of an ideal single-phase transformer; 3000VA, 380V/220V’ tour. If the network frequency…

Q: A transformer takes a No load current of 0.22 A and power factor of 0.547 lag, when its primary is…

A: Given, No load current (Io)= 0.22 A No load power factor= 0.547 lagging No load supply voltage…

Q: The transformer shown operates at 50Hz with the turn numbers N1=200 and N2=100 for primary and…

Q: A 20-kVA, 440/220 V, 1-phase, 50 Hz transformer has iron loss of 324 W. The Cu loss is found to be…

A: A 20-kVA, 440/220 V, 1-phase, 50 Hz transformer has iron loss of 324 W. The Cu loss is found to be…

Q: A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and secondary…

Q: 4.1 Assume that an ideal transformer used to step down 13.8–2.4kV and that it is fully loaded when…

A: Given:Transormer is ideal,Hence, the i/p KVA = o/p KVAVoltage rating 13.8 kV/ 2.4 kVAlso, o/p KVA =…

Q: A 150-kVA single-phase transformer has a core loss of 1.5 kW and a full-load Cu loss of 2 kW.…

Q: Q2: A 5kVA, 200/400V, 50Hz single phase transformer gave the following test figures: No-load:…

A: Given values are = 5kVA, 200/400V, 50Hz single phase transformer. Tests results are = No-load:…

Q: A two-winding transformer is rated at 60-kVA, 240/1200-V, 60-Hz. When operated as a conventional…

Q: Q1 Calculate the daily efficiency of a single-phase transformer with an output capacity of 350 kVA…

Q: Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding…

Q: A 150-kVA simple-phase transformer has a core loss of a 1.5kW and a full-load Cu loss of 2 kW.…

A: In this question we need to find a efficiency of the transformer at the given condition.

Q: A 10KVA single-phase transformer provides a no-load secondary voltage of 110 volts. If the…

Q: . A 15kVA single-phase transformer, for 10000V/440V at no load, has resistances and leakage…

A: In this question, We need to determine the value of the secondary voltage at full load, 0.85 power…

Q: (a) A 5 MVA 230/11.5-kV single-phase power transformer has a per-unit resistance of 1.5% and a…

Q: Q1 Calculate the daily efficiency of a single-phase transformer with an output capacity of 350 kVA…

A: The solution can be achieved as follows.

Q: 3. A single-phase 100-kVA, 7200-V/120-V, 60HZ distribution transformer is used as a step down…

A: transformation ratio, primary side impedance, secondary side impedance, primary and secondary side…

Q: The primary and secondary windings of a 500-kVA, 11-kV/415-V, single-phase transformer have…

Q: A, determine V½ l, Z, and the impedance Z',, which is the value of Z, referred to the primary side…

A: Given: N1=1000N2=250V1=1000∠0°I1=5∠30° The relation between voltage and the turns of the transformer…

Q: A 5000-KVA 230/13.8-kV single-phase power transformer has a per-unit resistance of 1 percent and a…

A: In this question we need to find a equivalent circuit referred to LV side of transformer , voltage…

Q: A 20-KVA, 20,000/480-V, 60-Hz distribution transformer is tested with the following results:…

A: Given Parameters of a distribution transformer. We need to sketch the per equivalent circuit.…

Q: A 240-kVA, 480/4800-V, step-up transformer has the following constants: Rs = 2.5 Ω, Xs = j5.75 Ω, Rp…

A: Given step up Transformer with240 KVA, 480/4800 vRs=2.5 Ω,Xs=j5.75 ΩRp=25 mΩ,Xp=j57.5 ΩThe core…

Q: 2. A 4800/240-V, single phase transformer is rated at 10 kVA. It has an equivalent impedance…

A: Features: Transformer is a static device which transfers power from one circuit to another circuit…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

100%

Q/ An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4
kW and full-load Culoss of 1.6 kW. Determine (a) the kVA load for maximum
efficiency and the minmum efficiéncy (b)the efficiency at half full-load at 0.8
power factor lagging

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An ideal transformer has no real or reactive power loss. (a) True (b) False
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
For developing per-unit equivalent circuits of single-phase three-winding transformer, a common Sbase is selected for all three windings and voltage bases are selected in proportion to the rated voltage of the windings (a) True (b) False
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False