QI - A main pipe consist of 4 segments of equal length (500m for each segment), supplying 4 irrigation projects, the discharge for these projects are shown in the figure 1. Assume that the land is level and ignore any energy losses except friction losses He. Construct an optimal model to optimize the main line cost. Notes; 1- 0.5m's

QI - A main pipe consist of 4 segments of equal length (500m for each segment), supplying 4 irrigation projects, the discharge for these projects are shown in the figure 1. Assume that the land is level and ignore any energy losses except friction losses He. Construct an optimal model to optimize the main line cost. Notes; 1- 0.5m's

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 me- ters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? PLEASE INCLUDE FIGURE AND DERIVATION
water has to supplied to a town with with one lakh population at the rate of 150lpcd for a river 2000m away. The difference in elevation between the lowest and reservoir is 36m. If the demand has tu be supplied in 8 hours,Determine the size of main and the water horse power.Assume maximum demand 1.5 times the average demand. Assume f = 0.0075 velocity in the pipe 2.4m/sec
Consider that water is pumped a distance equal to the last three digits of 917551848 in kilometer from a reservoir (Reservoir A) at mean sea level elevation to a second reservoir (Reservoir B) at elevation 50 ft. above mean sea level. The pipeline connecting the reservoirs has a diameter of 60 in and is constructed of concrete with an absolute roughness of 0.003. If the flow is equal to 917551848 in liter per week and the efficiency of the pumping station is 75%, what will be the monthly power bill if electricity costs is the same as the highest rate of the electricity provider of your community in cents/kwh?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 me- ters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? (PLEASE USE BERNOULLI'S ENERGY EQUATION) AND INCLUDE COMPLETE SOLUTION
Q1. Analyse the following water distribution network by Hardy Cross method. 3x(Rolla x 10)/5 L/s K-3 K-1 K=2 K-2 Roll x 10 L/s Zx(Rolla x 10)/5 /s K-3 Note : Use Roll# = 20
1. A water district which serves a suburban community needs a new water transmission main which will supply the area from an existing reservoir. The line will be 8.5km long. The reservoir elevation is 85 meters, and the town elevation at point of discharge is 30 meters. No pumping will be provided, and the water will be delivered to a non-pressurized storage tank in town. The proposal is to build a single line of new smooth clean cast iron pipe f=0.021. The present demand is 1 million gallons per day. a. Determine the minimum diameter pipe that could be used. b. Determine the value of the Manning's n which would apply to the particular installation. (15 pts)
Irrigation and drainage, i need solutions in 15 minutes please. MCQ/A 30 cm diameter well completely penetrates a confined aquifer of permeability of 45 m/day. The thickness of the aquifer is 20 m. Under steady state of pumping the drawdown at the well found to be 3.0 m and the radius of influence was 300 m. Calculate the discharge of the well . A-0.0851 m³/min B-1.548 m³/min C-0.0258 m³/min D-0.258 m³/min
Design a 5.5-km forcemain (f = 0.012) to transport a flow of 250 L/s from a sewage pump station(Suction Level = 25.6 m) to a wastewater treatment plant (Inlet tank Level = 36.5 m). Estimate the requiredsewage pumps’ horsepower to deliver this flow (use secondary losses equal to 20% of main losses)
Since there is a need to supply more water from reservoir A to reservoir B, it is necessary to lay an additional pipe parallel to it. The existing pipe is 0.6m in diameter with a discharge of 0.5m³/sec between the two reservoirs and 6000m long. Assume f = 0.02 %3| for the old pipe and f = 0.25 for the additional pipe. Determine the following: %3D a. If the additional pipe will have a discharge of 0.65m³/sec of the same length and the head difference between the two reservoirs is constant, find the pipe diameter. ANSWER: h= 25m Existing Pipe Q=0.50m³/sec D = 0.697 m в Additional Pipe b. If the additional pipe of 0.6m in diameter is laid out from the original pipe at its midpoint towards reservoir B, find its capacity. Assume f = 0.02. Also solve for the change in the %3D flow or discharge from A to B. ANSWER: Existing Pipe h=25m QA = 0.7232m/s, QB = 0.3923m³/s, %3D AQ = QA – Q = 0.5271m³/s %3D | в `Additional Pipe
1Two water pumps are arranged in series. The performance data for both pumps follow the parabolic curve fit Havailable =HO =aV ^2. For pump 1, HO =5.30 m and coefficient a =0.0438 m/Lpm^2; for pump 2, HO =8.70 m and coefficient a =0.0347 m/Lpm^2. In either case, the units ofnet pump head H are m, and the units of capacity V are Lpm.Calculate the combined shutoff head.
ACTIVITY PIPES IN SERIES AND PARALLEL & RESERVOIR PROBLEMS 1. A pipe network consists of pipeline 1 from A to B, then at B it is disconnected to pipelines 2 and 3, where it merges again at joint C to form a single pipeline 4 up to point D. Pipelines 1, 2, and 4 are in series connection whereas pipelines 2 and 3 are parallel to each other. If the rate of flow from A to B is 10 L/s and assuming f = 0.02 for all pipes, determine the flow in each pipe and the total head lost from A to D. Pipeline 1 Length (m) Diameter (mm) 3000 200 2 2200 300 3 3200 200 4 2800 400 A 1 B 2 3 C
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 300 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump?(PLEASE INCLUDE DRAWING) USE BERNOULLI'S ENERGY EQUATION