Q5. Two shunt generators operate in parallel to supply a total load current of 200A. Each machine has an armature resistance of 0.52 and a field resistance of 1002. If the generated EMFS are 200V and 210V respectively. Determine: I- Draw the cireuit setup and determine the load voltage and load power II- Find the armature current of each machine and the power supplied.

Q5. Two shunt generators operate in parallel to supply a total load current of 200A. Each machine has an armature resistance of 0.52 and a field resistance of 1002. If the generated EMFS are 200V and 210V respectively. Determine: I- Draw the cireuit setup and determine the load voltage and load power II- Find the armature current of each machine and the power supplied.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

5. Two shunt generators A and B operate in parallel and their load characteristics may be taken as straight lines. The voltage of A falls from 240 V at no-load to 220 V at 200 A, while that of B falls from 245 V at no-load to 220 V at 150 A. Determine the current which each machine supplies to a common load of 300 A and the bus-bar voltage at this load.
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
A thicker wire is used in the DC series field winding than DC shunt field winding in DC machines. * O because it carries the load current. O to prevent mechanical vibrations. O to provide strength. O to produce large flux. The speed of a DC motor can be changed by varying - armature resistance circuit O flux per pole O voltage source O all of above
Two shunt generators A and B operate in parallel and their load characteristic s may be taken as straight lines. The voltage of A falls from 240 V at no - load to 220 V at 200 A, while that of B falls from 245 V at no - load to 220 V at 150 A. Determine the current which each machine supplies to a common load of 300 A and the bus - bar voltage at this load.
Q3/ A/ Compare between de series and shunt generator. Q3/ B/ Briefly explain the commutating process in dc machine.
Draw and explain a typical power curve for a wind turbine and write the definition of the four important terms that are shown in the power curve
Two DC generators, each with armature resistance of 0.02 ohm and fieldresistance of 50 ohms run in parallel and supply a total current of 1000 amperesto the load circuit. If their emfs are 270 V and 265 V, their bus bar voltagewill be. [Ans. 267.5 V]
Two shunt generators are connected in parallel to supply a current of 1500A. Each machine has a field resistance of 60 ohms and an armature resistance of 0.01 ohm. The generated emf by each machine are 455V and 460V, respectively. Calculate the power delivered by each machine.
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www Ish1 Rh1 a.350-360 V b.450-460 V c. 550-560V Rat www az G₂ Raz 5000 A Ish2
Discussion:- 1. What do you understand by "armature- reaction"? Discuss the effect of armature reaction in an alternator when it is loaded with resistive, inductive and capacitive loads. 2. Give the value of voltage regulation for different power factors at full load current and interpret their values.
) A d.c. shunt machine while running as generator develops a voltage of 240 V at 1000 rp.m. on no-load It has armature resistance of 0.52 and field resistance of 250 92. When the machine runs as motor, input to it at no-load ts 4 A at 240 V. Calculate the speed and efficiency of the machine when it runs as a motor taking 40 A at 240 V. Armature reaction weakens the field by 6%