please solve the question during 20 mint Q37 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of aS0 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive lead of 160 kNdetermine the load carried by the steel rod and the brass bush and the compressive stress set up in cach materialFor steel, E= 210 GN/m, for brass, E - 100 GN/m.

Answered: Image /qna-images/answer/49248150-aca1-403c-8373-f550e091cba0.jpg

Q31 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a S0 mm diameter solid steel rod. If the compound bar is then subjected to an atial compressive lead of 160 kN determine the load carried by the steei rod and the brass bush and the compressive stress set up in cach material For steel, E- 210 GN/m, for brass, E- 100 GN/m.

Q31 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a S0 mm diameter solid steel rod. If the compound bar is then subjected to an atial compressive lead of 160 kN determine the load carried by the steei rod and the brass bush and the compressive stress set up in cach material For steel, E- 210 GN/m, for brass, E- 100 GN/m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.21P: A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular...

See similar textbooks

Similar questions

A solid bar of circular cross section (diameter d) has a hole of diameter d/5 drilled laterally through the center of the bar (sec figure). The allowable average tensile stress on the net cross section of the bar is s allow. (a) Obtain a formula for the allowable load P allowthat the bar can carry in tension. (b) calculate the value of P allowif the bar is made of brass with a diameter d = 1.75 in. and s allow= 12 ksi. Hint: Use the formulas of Case 15. Appendix E.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.