Q3 The beam has a rectangular cross section and is made of and elastic-plastic material having a stress strain diagram as shown. Determine the magnitude of the moment M that must be applied to the beam in order to create a maximum strain in its outer fibre of € max = 0.008. to (MP) 200 0004 (mm/mm) 200 mm 400 mm

Q3 The beam has a rectangular cross section and is made of and elastic-plastic material having a stress strain diagram as shown. Determine the magnitude of the moment M that must be applied to the beam in order to create a maximum strain in its outer fibre of € max = 0.008. to (MP) 200 0004 (mm/mm) 200 mm 400 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Similar questions

The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
The strain in the x structural-steel beam is direction at point A on the A-36 measured and found to be €x = 100(106). Determine the applied load P. What is the shear strain Yxy at point A? Take E=203 GPa and G-76 GPa. -0.9 m- mm -1.2 m- 50 mm TAL 1300 mm 4T 150 mm
The bar is made of an aluminum alloy having a stress–strain diagram that can be approximated by the straight line segments shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is Pmax = 0.05.
A pipe is subjected to a tension force of P = 45 kN. The pipe outside diameter is 41 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 120 GPa. Determine the normal strain in the pipe. Select one: a. 0.001263 mm/mm b. 0.000535 mm/mm c. 0.000568 mm/mm d. 0.000794 mm/mm O e. 0.001382 mm/mm f. None
A pipe is subjected to a tension force of P = 180 kN. The pipe outside diameter is 42 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 210 GPa. Determine the normal strain in the pipe. Select one: O a. 0.001263 mm/mm O b. 0.000535 mm/mm O. 0.000568 mm/mm O d. 0.000794 mm/mm O e. 0.001382 mm/mm O f. None
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 a. Determine how much the wire stretches when the horizontal force acts on the pole. 3 ft 30 D 2.5 kip 4 ft B b. Determine the change in the wire's radius c. At what angle is the principal stresses on pole BC? Use Mohr's Circle. d. What is the principal stress in pol BC? Use Mohr's Circle e. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. f. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) g. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. h. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
A beam is made from polypropylene plastic and has a stress–strain diagram that can be approximated by the curve shown. If the beam is subjected to a maximum tensile and compressive strain of P = 0.02 mm>mm, determine the moment M.
Two fully loaded tractor trailers travel over the bridge putting substantial loading on the structure. As they pass over the middle of the bridge, one of the vertical supporting pillars, which is fixed at its bottom, deforms as shown below. The weight of the trucks causes point T to move to point T'—a distance of 2.5 cm along the x-axis. If the pillar has an original height of 27 m , find the shear strain at point T.
A steel bar of 3 m long and 2500 mm2 in area hangs vertically, which is securely fixed on a collar at its lower end . If a weight of 25 KN falls on the collar from the height of 10 mm , determine the stress induced in the bar. What will be the strain energy stored in the bar? Take E=200 GPa.
A pipe is subjected to a tension force of P = 70 kN. The pipe outside diameter is 32 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 180 GPa. Determine the normal strain in the pipe. P Select one: O a. 0.001263 mm/mm O b. 0.000535 mm/mm O c. 0.000568 mm/mm O d. 0.000794 mm/mm e. 0.001382 mm/mm O f. None
The head H is connected to the cylinder of a compressor using six 316-in. diameter steel bolts. If the clamping force in each bolt is 800 lb, determine the normal strain in the bolts. If sY = 40 ksi and Est = 2911032 ksi, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released?
The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. If a load of P=60 kN is applied to the specimen, determine its new diameter and length. Take v = 0.35. o (MPa) 490 e (mm/mm) 0.007