Q3: In the orifice meter exper we found the following data of sample: The volume of water through 15 second is 315 mL, the diameter of the prifice meter is 6mm, and the height of the tank in (mm) is 300 the vertical distance of the needles (2) and (7) is 3 and 9 cm respectively. Find for two the needles listed above: 1-Cofficient of discharge 2- Coefficient of velocity. 3- Coefficient of contraction. ontracti

Q3: In the orifice meter exper we found the following data of sample: The volume of water through 15 second is 315 mL, the diameter of the prifice meter is 6mm, and the height of the tank in (mm) is 300 the vertical distance of the needles (2) and (7) is 3 and 9 cm respectively. Find for two the needles listed above: 1-Cofficient of discharge 2- Coefficient of velocity. 3- Coefficient of contraction. ontracti

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?
QUESTION 1 Three pipes A, B, and C are interconnected as shown in figure 1. The pipe dimensions are as follows: D (cm) 15 10 20 Pipeline L (m) 300 0.01 B 240 600 0.01 0.005 A 15 m 25 m B Figure 1 1.1 Find the rate at which water will flow in each pipe, ignoring the shock losses at P and entry to pipelines A and B. 1.2 Find the pressure at P.
B. Read are these sentences and choose the True or False. Answer only five 3-The Fluid friction apparatus in (major losses turbulent flows experiment) it is: h/ u V hoc u Log Ihl Where: h:the loss of head due to pipe friction. u :the velocity. 4- The Reynolds number is a ratio of an inertia force operation to a viscous force. Log lul
(b) A pitot-static probe is use to determine the flow velocity by measuring the differential pressure. The pitot formula to obtain the flow velocity is, 2(P- P,) V = where, V is the velocity, P is pressure and pis fluid density. i) The pressure difference sensor use in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/V. If the measured fluid is water at 20°C, determine the pressure difference inside the system the water velocity. ii) The Pitot-static tube is also commonly use in aircraft. An aircraft flying at 3000 m above sea level when the differential pressure reading clocked 3 kPa. Determine the speed of the aircraft.
Three pipes A. B, and C are interconnected as shown in figure 1. The pipe dimensions are as follows: Pipeline A D (cm) 15 10 L (m) 300 240 600 0.01 0.01 0.005 B 20 A 15 m 25 m B Figure 1 1.1 Find the rate at which water will flow in each pipe, ignoring the shock losses at P and entry to pipelines A and B. 1.2 Find the pressure at P.
Here are these questions if I could get help with themIf a spherical storage tank holds 40,000 gallons (120,000 liters) of water,what diameter must it have?If a cylindrical storage tank has a 40-foot (12 m) diameter circular 05::=how high must it be to hold 1 million gallons (3 million liters)?If water is moving at a rate of 3.2 ft3/sec (90,000 cc/sec), how manygallons (liters) per minute is this?If the specific gravity of gold is 19.0. what is the weight of a cubic inch(cubic centimeter) of gold? A cubic foot (cubic meter)?
A sealed tank filled with a fluid which is maintained at 0.35 bar gauge and 20 0C. The fluid discharges to the atmosphere (1.013bar) through a small opening at the side of the tank (z1 = z2 ). a) Calculate the velocity of fluid leaving the tank; assume the flow to be compressible and the process to be frictionless adiabatic.b) Calculate the velocity of fluid leaving the tank if the flow is incompressible and the process to be frictionless.c) Compare the calculated velocities and comment on the result. Take for fluid,α=1.0P=kρɤ ɤ =1.4R=287 J/kg.KMach number<0.3, incompressible flow. (Fluid Mechanics Question) (Please solve step by step)
A 100 mm by 50 mm Venturi meter is installed in a 100 mm diameter pipe to measure the flow of a certain liquid (sp gr 1.20). A differential gage connected with the inlet and throat contains a substance (sp gr 1.5) in the lower part of the tube, the remainder of the tube being filled with the certain liquid. The difference in height of substance columns in the two legs of the tube is 75 cm. If the coefficient of the meter is 0.97, compute the actual discharge.
3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter, is at the same level as the outlet, 203.2 mm in diameter. At the inlet, the vacuum is 152.4 mm Hg. The center of the pressure gauge connected to the pump discharge flange is 122 cm. The gauge reads 138 KPag. For a pump efficiency of 83%, what is the power output of the motor? 122 cm. PUMP
pls ans asap Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the diameter of the pipe, in millimeter (mm), that was used is
Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be finalized for a flow rate of 3299.5 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 3.6 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines Area of the maximum sized pipe diameter (in m2) Area of the minimum sized pipe diameter (in m2) The minimum sized pipe diameter (in cm) and The maximum sized pipe diameter (in cm)
Q4/ An orifice meter is used to measure the rate of flow of a fluid in pipes. The flow rate is related to the pressure drop by the following equation: |ΔΡ u = c where u = fluid velocity AP = pressure drop (force per unit area) p = density of the flowing fluid C = constant What are the units of c in the SI system of units?