Q2/A circular jet of water at 200C impinges on the vane shown in figure. The incident jet has a velocity of 25 m/s and a diameter of 200 mm. The vane divides the incident jet equally, and the jet exits the vane as two jets, each making an angle of 200 with the incoming jet. (a) Determine the force on the vane when the vane is moving at a speed of 15 m/s in the same direction as that of the incident jet. (b) Determine the force on the vane when the vane is moving at a speed of 15 m/s in the opposite direction to that of the incident jet. Assume water at 200C.

Q2/A circular jet of water at 200C impinges on the vane shown in figure. The incident jet has a velocity of 25 m/s and a diameter of 200 mm. The vane divides the incident jet equally, and the jet exits the vane as two jets, each making an angle of 200 with the incoming jet. (a) Determine the force on the vane when the vane is moving at a speed of 15 m/s in the same direction as that of the incident jet. (b) Determine the force on the vane when the vane is moving at a speed of 15 m/s in the opposite direction to that of the incident jet. Assume water at 200C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

27. Refer to Figure 13. What is the reaction at B? a. 275 N b. 375 N c. 475 N d. 575 N FIGURE 13 300 N/m В 3 m 1.5 m
1. Consider a water jet having a diameter of D = 1 cm and a flow of Q = 1 L/s. The jet is deflected by a fixed plate which is inclined at an angle of 50° from horizontal. a) Determine the velocity vx in the x-direction in m/s. b) Determine the velocity vy in the y-direction in m/s. c) Determine the resultant force Fx on the plate in the x-direction in N. d) Determine the resultant force Fy on the plate in the y-direction in N. e) Determine the combined resultant force F on the plate in N. 1 L/s 50° V = 6 m/s
A 2-in diameter water jet with a velocity of 100 fps shown below impinges on a single vane moving in the same direction (see U1 =60 fps). If the angle B2 is equal to 150 degrees and friction loss over the vane makes V2 = 0.9V1, compute the reaction forces in both the x and y direction. the vane (magnitude and direction). V = 100 Uj = 60 %3D Bz = 150° %3D
q3(c) A jet of water (at 10°C) of diameter 2.5 cm flows freely in the atmosphere in a horizontal plane with the initial velocity of 6.5 m/s is deflected by a curved vane 90°. (i) Illustrate the force diagram. (ii) Calculate the forces exerted on the water by the vane in x- and y- direction.
The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D shown in the figure below is 300 mm² and a modulus of elasticity is 105 GPa. A single force P-90 KN acts on the Kafcs system from point A as shown in the figure. Determine the vertical displacement at point A using the work-energy method. 2 m B P 1.5m
Problem (2) A uniform slender rod of mass m is released from rest when 0 = 0°. Determine the magnitude of the reactive force exerted on it by pin B when 0 = 90° as a function of mg. A
A flat plate is placed normal to a discharging jet of water. The jet discharges water at the rate of 0.2 m³s-¹ and at a speed of 18 ms 1. The force on the plate due to the jet, if the collision is inelastic is:
Consider the simply-supported overhang beam shown. There is a pin support at A, a roller support at D, and an overhang of 2m. Calculate the support reaction at D. 5kN/m 2kN/m B 3m 2m- 1m 2m 2m
7. A nozzle discharges 100 L/s with a velocity of 24 m/s and is inclined 45° downwards. The jet coming out of the nozzle strikes an unsymmetrical two-cusped vane that is moving at a velocity of 6 m/s along the horizontal plane. Half of the jet is deflected upwards 45°and the other half is deflected downwards 90°. Determine the x- and y-components of the force exerted by the jet on the vane. vane
1. consider the system shown wherein force P = 250N and couple M = 100 N-m. Assuming a = 30° and B = 45°, /B = 45° B M= 100N-m 300 mm P= 250N ja= 30° 200 mm a. Which of the following force and couple set acting at point A is equivalent to the force and couple applied to the system? A B 20.7N-m 300 mm 20.7N-m 300 mm 45°m 45°m Y 250N 250N D 221N-m 300 mm 221N-m 300 mm 45m 45m 250N 250N b. Which of the following shows a single force equivalent to the force and couple applied to the assembly shown above? A B 18 J45300 mm 45° 00 mm 200 mm 321 mm 250N 250N A 200 mm 200 mm B 300 mm 95.8 mm 300 mm 85.9 mm 45 A 200 mig50N A 200 msON 250N
3. The mass C is connected by two wires to the vertical shaft AB. Rotation of the shaft causes the mass to travel in the horizontal circle shown. Calculate the speed vo of the mass that would result in equal tensions in the wires. 25° 0.6 m 50⁰ VO
The P force of intensity 30N is applied perpendicular to the BC portion of a curved bar, as shown in the following figure. Determine the moment of force P in relation to point B and the moment of force P in relation to point A.