Q2. Two 35 mm shafts are connected by a flanged coupling The flanges are fitted with 6 bolts on 125 mm bolt circle. The shafts transmit a torque of 800 N-m at 350 rp.m. For the safe stresses mentioned below, calculate 1. diameter of bolts ; 2. thickness of flanges; 3. key dimensions; 4. hub length; and 5. power transmitted. Safe shear stress for shaft material = 63 MPa Safe stress for bolt material Safe stress for cast iron coupling Safe stress for key material = 56 MPa = 10 MPa = 46 MPa %3D

Q2. Two 35 mm shafts are connected by a flanged coupling The flanges are fitted with 6 bolts on 125 mm bolt circle. The shafts transmit a torque of 800 N-m at 350 rp.m. For the safe stresses mentioned below, calculate 1. diameter of bolts ; 2. thickness of flanges; 3. key dimensions; 4. hub length; and 5. power transmitted. Safe shear stress for shaft material = 63 MPa Safe stress for bolt material Safe stress for cast iron coupling Safe stress for key material = 56 MPa = 10 MPa = 46 MPa %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
1. Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a flange coupling having five bolts with a 100 mm bolt circle. The design shearing stress of the bolt is 12 MPa and design compressive stress of the flange is 15 MPa. a. What is the power in kW transmitted by the short shaft? b. What is the torque transmitted by the shaft in Ib-in? c. What diameter in mm of bolt should be used? d. How thick should the flange be in mm?
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa., G70 Gpa (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameter d if it is operated at 3000 rpm? (c) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor GIC G
(7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the crankshaft @ the upper end & bearing @ the lower end 560mm apart. (a) If the engine develops 15kW @ this speed, what is the diameter of the solid steel shaft to use? The allowable torsional stress is 80N/mm².
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
A collar is fitted as a tight fit on a solid shaft. made before assembly in measuring, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel E=2.1x105 N/mm2 , Tmax = P (1/QG^2)
Two 35 mm shafts are connected by a flanged coupling. The flanges are fitted with 6 bolts on 125 mm bolt circle. The shafts transmit a torque of 800 N-m at 350 rpm. For the safe stresses mentioned below, Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa %3D Safe stress for key material = 46 MPa Calculate: (i) diameter of bolts ; (ii)thickness of flanges ; (iii)key dimensions ; (iv)hub length; and (V)power transmitted.
Problem 1 only, solve carefully, include the units and dra the diagram. Thanks! . A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, findA. Force that will shear the pin, kNB. Shear pin diameter, mm
(a) (b) Q5: A steel shaft is to transmit a stable torque of 1400 Nm to the steel spur gear through a Type B square end key with the dimensions L=140 mm and b=14 mm. What should be minimum height of the key to transmit the power safely. The allowable bearing stress is 90 MPa.
A keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. (Ans: 4.33 cm)
Design a flanged coupling that will be able to carry power of 1,500 HP using a factor of safety of 3.3 at 630 rpm. The shaft diameters of the equipment the coupling will connect are both 5 inches. Check your design for the following stresses if N = 3.3 is satisfied: 1. Bolt shearing; 2. Bolt bearing; 3. Shearing of hub from coupling flange; 4. Shear on key; 5. Compression on key; Select dimensions whichever is higher. 6. Calculate also minimum length of engagement of the bolt and nut if these are of the same material. 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only Instructions: