Q2) A state of plane stress is given by g =- 32MPA, g = 16MPa and Txy = 10MPA. Use Mohr's stress circle to determine a) the maximum shear stress and its location; b) the principal stresses and principal directions; c) the state of the stresses on a plane inclined at an angle of +40° to the x- axis.

Q2) A state of plane stress is given by g =- 32MPA, g = 16MPa and Txy = 10MPA. Use Mohr's stress circle to determine a) the maximum shear stress and its location; b) the principal stresses and principal directions; c) the state of the stresses on a plane inclined at an angle of +40° to the x- axis.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
A plane stress state is given as follows (50MP in the bottom right corner denotes the shear component, and others denote the normal components). 1) Please draw the Mohr's circle of this plane stress state. Indicate the center of the circle, the radius of the circle, and the point that corresponds to x-plane (the normal of the plane is x axis) 2) Determine the principal stresses and directions of this stress state using Mohr's circle. 3) Draw the stress element to show maximum shear stress 71, T2, and the corresponding normal stress. 75 MPa 50 MPa 50 MPa
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
Asap
For the stress state shown. Ox = 40 MPa MPa Oy = 80 MPa Txy %3D 65 Oy Txy Using Mohr's Circle, a) Find the principle stresses and draw the stress state in the principle orientation b) Find the maximum in-plane shear stress and draw the stress state in the maximum in-plane shear stress orientation
2) The state of stesss at a point in a body relative to the xyz coordinate system is: 2 3 -5 [o]= 3 2 kpsi 6. %3D -5 2 -4 a) Determine the principle stresses and the direction cosines corresponding to each principle stress. b) Draw the 3D Mohr's circles. c) Determine the maximum shear stress. d) Find the orientation of the plane containing the maximum shear stress relative to the original axis system 3) For the stress tensor in problem 2: a) Determine the normal and shear stress on a surface intersecting a plane defined by 3 points (0,0,0); (2,-1,3); (-2,0,1) b) Give the magnitudes of these stresses and the direction cosines defining their directions.
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
Question 2: An element in plane stress is subjected to stresses, ox = 16000 MPa, o, = 6000 MPa, and Txy = Tyx = 4000 MPa (as shown in figure below). Using the Mohr's circle, determine the following: A) The stress components with respect to ab axes which are inclined at 0 = 45° to the xy аxes. B) Locate the principal axes and evaluate principal stresses. C) Locate the axes of Maximum shear stress and evaluate the corresponding stress components. yt -9000 MPa a 5000 MPa 30° 12000 MPa Fig. Q1: An element in plane stress If the values of txy = Tyx = 0 and the element is subjected only to stresses, ox = 16000 MPa, Oy = -6000 MPa D) What are the differences of the results of A, B, and C above ? E) Discuss the differences.
For a point under a plane state of stress, the stresses on the vertical and horizontal planes are shown in the figure below. 100 MPa 48° 80 MPa 60 MPa Using only the stress transformation EQUATIONS, determine the following: a) The normal stresses on the plane oriented along plane a-b. o, = b) The shear stress on the plane oriented along plane a-b Ty'= c) The locations of the principal planes (express your answers as angles made by the principal planes with respect to the horizontal) Op2= d) The principal stresses Op1= Op2= e) The maximum in-plane shear stress Tmaxip= Show the results of both stresses in plane a-b and principal planes on a sketch of the plane on which these stresses act.