Q.28: For the circuit shown: V,-150cos500t Volt500 lurns1. Specify the numerical value of R for maximum212 20MITpower dissipated.2. Compute the maximum power dissipated in RL.RLV,1000turns(Ans.: RL=232 & Pmax=461.14W)Tideal

Answered: Image /qna-images/answer/110e7d50-bbb2-4f2c-acc7-229c0151d4d3.jpg

Answered: Q.28: For the circuit shown:…

Q.28: For the circuit shown: V,-150cos500t Volt 1. Specify the numerical value of RL for maximum power dissipated. 2. Compute the maximum power dissipated in RL. (Ans.: RL=232 & Pmax=461.14W)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

GIVE DETAIL EXPLAIN PLEASE! with cicruit drawing.. Ans : Rth = 28 ohm Vth = 92 V.
Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.
please give detail explain.. Ans : Rth = 28 ohm Vth = 92 V
QUESTION 1 Design a high efficiency 3.3 V, 5A d.c.to d.c. power converter from a 4 to 5.5 Vdc source. The maximum allowable inductor current ripple and output voltage ripple are 0.1A and 20 mV, respectively. Assume a switching frequency of 20 kHz. a) Design a suitable converter power circuit using a MOSFET switch, showing all calculation of inductor and capacitor values and drawing a circuit diagram of the final design including component values. Indicate the peak inverse voltage and forward current rating of any diode required, and the maximum drain- source voltage of the MOSFET. b) On the Schematic diagram, draw the path of the current flow during the ON time and the OFF time. c) Describe the effect of changing the values of the inductor and the capacitor in the circuit. d) What is the effect of switching frequency in the circuit? e) Draw the schematic diagram of a circuit with the output voltage higher than the input voltage.
Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
JXM2 Q.6: For the circuit shown if Vs=1020°v: J62 452 J524 1. Find the value of "XM" that makes the Vs 52 -J42 current through (5Q) resistor equal zero? 2. Calculate the value of total dissipated power. (Ans.: XM=20 & P7=16W)
Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ
3 A peak rectifier (peak tollower) Cir cuit is gian below. Vs is a GOH3 Sinuscidal Vollge with peak value Upz50V. 50V. The load resistance R= Sk . Find the Vallke of the capacitance C Such that the peak- to-peak ripple 2 volts. (idenl diede) Voltage Vr Vs
The regulator In figure provides 6v load voltage for all load currents, IL s.5A. The unregulated supply (Vs) varles between 8 and 10 V, and the zener dlode provides regulation for Iz >0, determine a. Series resistance (Rs) that will maintain output voltage fixed at GV. b. Maximum current through Zener diode. c. Calculate 15 Hill power dissipation rating of the zener dloud. V₂ (6V) R₁
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
1. The DC-DC converter has several circuit configurations. a) (Draw a simple connection of IGBT switch, diode and inductor that can discriminate between Buck, Boost and Buck-Boost converter circuits respectively.) b) ('A Boost converter produces an output voltage, Vo that is more than or equal to the input voltage, Vi. Based on this statement develop the equation for the relationship between Vo Viand D. where D represents the duty ratio. You can use any suitable diagram to illustrate your answer.)
I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (KBJ1008). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.