Q.2 Determine the magnitude and the location of the resultant of the parallel force system given below. The force system acts on horizontal beam AB all force are vertical. The load intensity of the distributed load w = 30 N/m. draw the load diagram with distributed load replaced by its resultant, and find the resultant of the force system and its location neglect the weight of the beam. 50 N w= 30 N/m A B 4 m 2 m 1 m

Q.2 Determine the magnitude and the location of the resultant of the parallel force system given below. The force system acts on horizontal beam AB all force are vertical. The load intensity of the distributed load w = 30 N/m. draw the load diagram with distributed load replaced by its resultant, and find the resultant of the force system and its location neglect the weight of the beam. 50 N w= 30 N/m A B 4 m 2 m 1 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.104P

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
1) What is the resultant summation of forces FCA and FDA? Write the resultant force in Cartesian vector notation. Please retain your answer as it will needed for other problem(s) (1 PA=500 lb 14 fi FA=400 lb D>
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 222 N and the couple M = 610 Nm. M N m A 150 N 300 mm -250 mm- P N 400 mm 90 N Answer: Determine the angle (in degrees) that the resultant makes with the positive x-axis, which is in the same direction as the horizontal force P. Answer: If the resultant force calculated in Q8 is placed at A, determine the magnitude of the couple created in Nm. Answer: Determine the distance from A (in m) at which this resultant should be placed so that the system is replaced entirely by a single force. Answer: If the resultant force calculated in Q8 is placed at O, determine the magnitude of the couple created in Nm. AnSwer. Determine the distance from O (in m) at which this resultant should be placed so that the system is replaced entirely by a single force. Answer:
A ball (B) is stopped on inclined surface 30° with horizontal by a horizontal force p=100N. a. Resolve the force P in two rectangular components parallel and normal to the inclined surface. b. If another force T=50 N pull the ball in direction parallel to the inclined surface , replace this pair of forces by single force. c. Find the resultant of single force above.
4) Determine the total moment caused by the forces Fp4 and Fca about the plate diagonal that goes through point B (the dashed line). Write your answer in cartesian vector notation. FCA= 500 lb 14 ft FRA = 350 Ib FDA= 400 lb 3 ft-> 3 ft 3 ft 2 t 6 ft
Problem 3 w2 kN/m 7x kN/m From the figure, w1=11kN/m, w2=15KN/m w1 kN/m 1. Find the resultant of the forces 2. Find the location of the resultant from point B. 5m 5m Sm
Q1.4 An eyebolt is subjected to four forces (FI-12kN, F2-8kN, F3-18KN, F4-4kN) that act under given angles( a1 45 , a 2-100 , a 3- 205 , a 4-270 ) with respect to the horizontal (Figure). Determine the magnitude and direction of FA the resultant.
Q2: The sandbags on the beam create a distributed load , Find a single equivalent Resultant (R) and its location with respect to point (A). 2.5 kN/m 1.5 kN/m 1 kN/m 3 m 3 m 1.5 m-
Cord Number of Weights Length (cm) Angle with respect to +x-axis Components of Forces Along (x-axis) Components of Forces Along (y-axis) left 3 6cm Right 4 8cm Center 4 8cm X X X Total: X X X Resultant R= θR=
Problem 3 w2 kN/m 7x kN/m From the figure, w1=9kN/m, w2=13KN/m 1. Find the resultant of the forces 2. Find the location of the resultant from point B. w1 kN/m 5m Sm 5m
1. R is the resultant coplanar-concurrent forces composing of P, T, F, and each Q acting on a body. Find the magnitude of the fourth force Q and its angle with respect to horizontal, if P = 840N directed downward to the left at 20 degrees with the vertical, T = 890N is acting to the right along the horizontal, F = 530N is up to the right at 45 degrees with the horizontal and R = 1300N acting downward to the right 30 degrees with the horizontal. show solution, formula and the sketch of the FBD and pls write legible
1. R is the resultant coplanar-concurrent forces composing of P, T, F, and each Q acting on a body. Find the magnitude of the fourth force Q and its angle with respect to horizontal, if P = 840N directed downward to the left at 20 degrees with the vertical, T = 890N is acting to the right along the horizontal, F = 530N is up to the right at 45 degrees with the horizontal and R = 1300N acting downward to the right 30 degrees with the horizontal. Show your solutions in graphical and analytical method.