Q.2/ A pressune drop of 7o0 Kpa is measured over 300mof horizontal, lo(m diameter wrought iron pipe thattransports oil (s.g=o.9,2:10m/s). Calculatethe low vate ?lengthAns: 0.037:

Name: Q.2/ A pressune drop of 7o0 Kpa is measured over 300mof horizontal, l
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q.2/ A pressune drop of 7o0 Kpa is measured over 300mof horizontal, lo(m diameter wrought iron pipe thattransports oil (s.g=o.9,2:10m/s). Calculatethe low vate ?lengthAns: 0.037:

Given Data ∆p=700 kPa D=10 cm L=300 m SG=0.9

Answered: Q-2/ A pressune drop of Fo0 Kpa is…

Engineering

Mechanical Engineering

Q-2/ A pressune drop of Fo0 Kpa is measured over 30om of horizontal, lorm dianeter wrought iron pipe that transports oil (S.g=o.9,2:10m/s). Calculate the low vate ? leagth Ans: 0.037: m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump delivers water from a tank (A)X water surface elevation-110m) to tank B (water surface elevation= 170m). The suction pipe is 45m long and 35cm in diameter the delivered pipe is 950m long 25cm in diameter. Loss head due to friction hf1 = 5m and h2 3m If the piping are from pipe(1)= steel sheet metal pipe(2)= stainless – steel Calculate the following i) ii) The discharge in the pipeline The power delivered by the pump.
Jet water in Pipe with diumeter equal to Somm to velocity=30 - divided into fwo branches with (o-756) ancd the o ther with Cu.25Q] recPcetively un equal diameter. Compute fore CumPenen ts on the Plate sec Vュ

Q3/Head loss in a pipe is measured by the Equation, h; = f(L/d).(v/2g) Prove that this Equation can be written in the form, h;= 0.0826 f (L/d³).(Q?/2g) Q4/Three pipes No. (1), (2) and (3) are connected in par %D Ciquro No 12) DsecSure headc at iuınstic point c D and
Q8)A duct of 65 cm diameter and 15m long carries 120 m³/min of air. Find the pressure loss in the duct. (P₁=0.6 bar/m). 2 IW
In the pipeline in the figure, water is transmitted from a-tank to Bdepo with a flow rate of 40OL/s from plastic pipes. Pipe lengths are L1 = 20m, Lz=30m and bore diameters, D:=0.2 m, D2=0.4 m. Find the AH level difference between the two tank water surfaces. Take the kinematic viscosity of water v=4,25.10s m2/s. Loss of entry to the pipe Kbg=0,5 L1 =20 m D1=0,2m A ΔΗ Valve loss coefficient Kvalve = 10 valve Warehouse entry loss coefficient Kdg = 1 %3D Kao = [1- T Sudden expansion loss coefficient KAG L2=30m D2=0,4m
3 whot is the pressure in a 9.7-in bore horizontal pipe, :f the bore of the pipe norrows to 4.1 in downstreom where the pressure is 65 psig and 28,200 gal of fluid per hour with a speciic gravity (SG) of 0.87 is flowing? Neglect losses.
A paint shop in the water flow through the pipe in the radius r Q = 0.05 m /s, density p= 1000 kg/m 3 type. The pipe friction coefficient is Cf= 0.0075 and the local loss coefficient K = 10. Pressure drop in the pipe; AP = p 2C K %3D where the water velocity in the pipe can be calculated with V = Q/(r²). What should be the radius of the pipe so that the pressure drop that will occur in a pipe of L = 100 m length does not exceed AP = 200 000 N/ m 2? State the tolerance value provided by the result you found.
Examples & The Inlet to pump is 10.50m above the bottom of sump from which it draw water through a suction pipe. If the pressure at the pamp inlet is not to fall bellow 28 kN/m² absolute, work out the minimum depth of water in the tank 6.019 m O 15m 0 3.019 m O 9.019 m O 1.019 m O
For the parallel-pipe system of Fig. each pipe iscast iron, and the pressure drop p1 - p2 = 3 lbf/in2. Computethe total flow rate between 1 and 2 if the fluid is SAE10 oil at 20°C.
-Example the values. asystem total head. against for the initial condition, show below - give the Lallowiny data dynamic uiscosity of liquid Calculate capacity curve density S-1200 kgim3 Static head on Suction Side 7S-3m Static heac on discharge Side Zd= 7m inside diameter of pipe di = o.052m -pipe roughress E3D0.00045m. gas pressure aboue the liquid in the tank Side of the pump the Suction Ps= atmospheric pressure. gas pressure above the liquicd in the tank on discharge side of the pump. the dund Pd= atmesperic pressure
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
Find the discharge in nach pipe shown in fgure. The head available at A is 20m of water and the friction factor for each pipe may be taken 0.03. 100 mm diameter, 200m length B Atmosphere 100 mm diameter, 100m length 50 mm diameter