Problem. The truss shown in Figure 1 is made from seven members, each having a mass per unit length of 9 kg/m. determine the distance d (x) to where the lifting cole must be attached, so that the truss does not tip (otate) when it is lifted. Ignore the mass of the gusset plates at the joints and the thickness of the members can be neglected. 6m B Y A www 6m ~8-5m C 37 P 6m Figure 1 For Problem D

Problem. The truss shown in Figure 1 is made from seven members, each having a mass per unit length of 9 kg/m. determine the distance d (x) to where the lifting cole must be attached, so that the truss does not tip (otate) when it is lifted. Ignore the mass of the gusset plates at the joints and the thickness of the members can be neglected. 6m B Y A www 6m ~8-5m C 37 P 6m Figure 1 For Problem D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The Z section in Fig. (a) 1s formed from aluminum alloy 2024-T3 sheet. What compressive stress will start local buckling of an element of the member? kw=2.9 E=10,700,000psi .75 0.65 Flange 1.05 Web✓
For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI
Use the method of joints to calculate the forces in all the members of the truss shown in Figure 2 below. 20KN 30⁰ C Rc B RB 60⁰ A 5m Figure 2
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
The steel truss with E=200GPais loaded as shown in the figure. Determine the following: the following a) the deformation of member AB if the cross-sectional area is 2500mmb) the deformation of member AD if the cross-sectional area is 1800mm A 4.0m 200 KN B D 4.0m 1² 2.5m
Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
The members of the truss shown below have a cross-sectional area of 10,000 mm². Determine the stresses in members AB and AE in MPa. Indicate if the stresses are in compression or tension. 4 m 4 m E 20 kN 40 kN A -> C. 8 m-
The truss shown in the figure is applied with force P= 5kN %3D 1.50 m 1.50 m 150 m 2 m 2 m What is the force in member DE in kN? A.
For the plane truss shown below loaded with a 200 kN force, determine the amount of deformation in membes (AB) & (AD) if their cross- sectional areas are known to be AB= 2500 mm² & AAD = 2000 mm² (assume E 200 GPa) 4 m B D 200 KN 2.5 m
The beam shown in Fig. is made from two boards. Draw the shear stress at (A.B.C.D) to hold the hoards together along the seam where they are joined 6.5KN/ 150 4m D 30 mm 150 mm 30 mm
The stiffness coefficient 'k₁1' for the beam shown below is ΕΙ 2m Internal Hinge
The members of the truss shown below have a cross- sectional area of 10,000 mm2. Determine the stresses in members AB and AE in MPa. Indicate if the stresses are in compression or tension. 3 m- 3 m C 3. B E 40 kN 80 kN 6m-