Problem Statement Based on Problem 8-11 from the textbook. The man has a mass, m. He plans to scale the vertical crevice using the method shown. If the coefficient of static friction between his shoes and the rock is μs and between his backside and the rock is Hb, determine the smallest horizontal force his body must exert on the rocks in order to do this.

Problem Statement Based on Problem 8-11 from the textbook. The man has a mass, m. He plans to scale the vertical crevice using the method shown. If the coefficient of static friction between his shoes and the rock is μs and between his backside and the rock is Hb, determine the smallest horizontal force his body must exert on the rocks in order to do this.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

W Given: Block on a rough surface weighing 400 N Angle of internal friction is 21.8° Solve for the force P required to impend motion in the following situation: 1) If force applied to block horizontally. 2) If force applied to block downward at 30° with the horizontal. 3) What should be the minimum force P and its angle from the horizontal is required to start motion.
A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area. The correct answer is 2.84. Show solution.
PROBLEM 2.78 A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid supports as shown. For the type and grade of rubber used r =1.54 MPa and G=12.6 MPa. Knowing that a centric vertical force of magnitude P=13 kN must cause a 2.5-mm vertical deflection of the plate AB, determine the smallest allowable dimensions a and b of the block. 75 mm bnin = 56.3 mm = 20.5 mm a min
Question 30/50 SITUATION. Personal Space Person of mass 'm' walks on a plank resting on rough surfaces A and B. Given: m = 120 kg Coefficient of friction at A = 0.40 L = 4 m Coefficient of friction at B = 0.20 x=D30° B At what distance 'x' will the plank start to slide? O 2.33m O 1.69m 1.62m 2.29m Previous Next
PROBLEM 12.31 A 10-lb block B rests as shown on a 20-lb bracket A. The coefficients of friction are u, =0.30 and , = 0.25 between block B and bracket A, and there is no friction in the pulley or between the bracket and the horizontal surface. (a) Determine the maximum weight of block C if block B is not to slide on bracket A. (b) If the weight of block C is 10% larger than the answer found in a determine the accelerations of A, B and C.
PROBLEM 5 The uniform block, 4'x 3'as shown weighs 2001b. It is pulled up the incline by the force F= 250 lb. Determine the maximum and minimum values of d so that the block does not tip over as it slides up the incline. The coefficient of friction is 0.21. +3 IL
A cubic crate of side s = 2.3 m is top-heavy: its CG is 20 cm above its true center. 1) How steep an incline can the crate rest on without tipping over? Theta? 2) What would your answer be if the crate were to slide at constant speed down the plane without tipping over? [Hint: The normal force would act at the lowest corner.] Theta?
The force P is applied to the 600-lb block when it is at rest. Determine the following: A. The value of P required to keep the block from falling down the incline? B. The value of P required to initiate motion up the incline? C. The value of P required to keep it moving up? 35° P 60° Hs = 0.25 Hk=0.20 600 lb
A 5kg block is placed in a rough surface (µs = 0.30 and Hj = 0.25) inclined at a slope of 25 degrees and acted upon by a force, P directed 60 degrees with respect to the horizontal as shown in the figure. If the block is in impending motion to slide downwards: 60° 25° a. What is the magnitude of P applied on the block? b. What is the magnitude of the friction force f,? c. If you lessen the applied force P, such that P is lower than what you computed in item a, what will happen to the value of the frictional force?
Blocks A, B, and C have weights of 45 N , 29 N , and 10 N , respectively. (Figure 1) Part A Determine the smallest horizontal force P that will cause impending motion. The coefficient of static friction between A and B is us = 0.3, between B and C, u's between block C' and the ground, = 0.35. 0.4, and Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 HA Value Units P = Submit Request Answer Provide Feedback Next >
Determine whether the 15-kg block shown is in static equilibrium under the loadings shown, and report the magnitude of the friction force (in Newton) when P = 760 N and = 43 degrees at the state of static equilibrium. The coefficients of static and kinetic friction between the block and the rough inclined surface are shown in the picture. Report the friction force as positive when it is directed downward, and negative when it is directed upwards. 500 N Ms = 0.35 με = 0.25 35° P
Prob. 4 Consider a slender 2 meter uniform homogeneous 7-kg bar that rests on, and makes 45-degree angles with, a smooth vertical wall and a rough horizontal floor. What is the minimum coefficient of friction required to prevent the bar from slipping?