Answer Problem II only Please put detailed solution.Topic: Mechanics of Deformable Bodies Problem IThe beam loaded as shown is supported with a hinge support at A and a roller at B. Thetotal depth of the section is 465mm, the width of the flanges is 193mm, the width of the web is11mm and the depth of the flange is 19mm. Do the following:1. Determine the maximum flexural stress.2. Determine the maximum shear stress.3. Determine the deflection at point C.4. Determine the slope of the elastic curve at A.5. Determine the slope to the elastic curve at B.6. Draw the elastic curve.193 n19mm165 mProblem IIThree equal loads of 25kN each separated by 2m, roll as a unit across a 12-m simplysupported span.7. Determine the maximum moment8. Determine the maximum shear.

Draw F.B.D for given situation 7. Determine the maximum moment As maximum moment occurs at midspan…

Answered: Problem II Three equal loads of 25kN…

Problem II Three equal loads of 25kN each separated by 2m, roll as a unit across a 12-m simply supported span. 7. Determine the maximum moment 8. Determine the maximum shear.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar AD is supported by two steel wires of in. diameter (E = 29 x 8 in. 106 psi) and a pin and bracket at A. Knowing that the wires were initially taut, determine (a) the additional tension in E 10 in. B each wire when a 220-lb load P is applied at D, (b) the corresponding deflection of point D. 12 in. 12 in. 12 in.
Determine the safe span that a 100 * 150 mm purlin would have if it has a spacing 800 mm on centers, to carry a roof load of 60 Pa and a wind load of 1.4 kPa acting on the vertical surface. Allowable bending stress is 10 MPa and the allowable horizontal shearing stress is 0.4 MPa. The allowable normal deflection is 1/360 of span. Weight of purlin is 5 kN/m3 and E= 17.3GPa
A Ignore Internal Strain Energy due to axial load and shear. V A (pinned) 15ff 2 k/ff V V V C (hinge) 15 ft NO € (pireed) 1(A) = St 20 ft EI= constant E = 10,000 ksi I = 2,500 in M₂M - dx ΕΙ Find Horizontal Deflection EI=Constant E = 10,000 ks: I=2,500 in 4 On 6/9 at joint D using victual work 0
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
If the beam shown is supported by the fixed wall at B and the rod AC. if the rod has a cross sectional area = 7 x104 m² and is made of the same material of the beam if the area moment of inertia of the beam's cross section is 2.8 x 10-6 m4 if the distributed load w = 8 kN, then, the tension in the rod AC is T. 1m 1 m 2 m O a. 6.00 O b. 873.69 Oc. 59910.13 O d. 26.00
2.27 Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240 mm². Link CE is made of aluminum (E = 72 GPa) and has a cross-sectional area of 300 mm². Knowing that they support rigid member ABC, determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.35 mm. Q Search P A 125 mm D B (7 = 225 mm 225 mm 150 mm ↓ E 4) 8:51 AM 3/5/2023
ANALYZE THE STRUCTURE USING PORTAL FRAME METHOD. COMPUTE: AXIAL LOAD OF AD MINT ALL Onc MOMENT AT SUPPORT B MOMENT OF MEMBER EF ATE P E GOKN A 7m B 5m 8m
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
STRUCTURAL THEORY Show complete solution for better understanding Situation 1: From the truss shown, each member has a cross-sectional area of A = 400 mm 2, E = 200 GPa. Use the method of Virtual Work F b.-37.5 C.-30 d. 30 -2m- 1. Determine the stress on member AE a. 37.5 E c. 2 d.3 n B 45 KN 2 m 2. How many zero-force member are there? a. 0 b. 1 3. Determine the vertical deflection of joint E a. 1.42 b. 3.38 c. 2.95 d. 1.24 1.5 m
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel= 200 Gpa and a= 1.75 m, b= Im, d= 50mm, h= 10mm 2a
Determine the horizontal displacement of joint D. Each A-36 steel member has a cross-sectional area of 300 mm². Use the method of virtual work 4 kN 2 kN 3m 3m E A 3m -YOB
igid beam is hinged at one end and supported or linear elastic springs (both having a . Hness of 'K') at points '1 and 2', and an inclined load acts at 2', as shown. A Hinge 45° 451 Fixed 40. Which of the following options represents the deflections d, and 8, at points '1' and *2? 2(2P 4(2P (a) 8, = and ô, = (b) 8; = and ô, = ) (c) 8 : and ô, = ) %3D and 8, = ) 4( V2P & : (d) 8, %3D k