Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn waste chipper/shredder. As the engine operates at 1200 rpm, the shredding teeth should rotate at 240 rpm. The drive sprocket has 18 teeth. Determine an appropriate pitch for the chain, the number of teeth on the driven sprocket, the pitch diameters of both sprockets, and the chain speed. Also indicate the number of links in a suitable chain and specify the required center distance.

Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn waste chipper/shredder. As the engine operates at 1200 rpm, the shredding teeth should rotate at 240 rpm. The drive sprocket has 18 teeth. Determine an appropriate pitch for the chain, the number of teeth on the driven sprocket, the pitch diameters of both sprockets, and the chain speed. Also indicate the number of links in a suitable chain and specify the required center distance.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the pinion pitch and the gear is 80 mm and 100 mm. The shape of the gear gear was 14 restriction form. The static voltage allowed for both gear is 55 mpa. If the door transports to 2.95 kw power at the turn of 1200 RPM, identify the module and the number of teeth on each gear from the Angle of power and check the design from the Angle of the tear. Take the surface durability limit is 630 mpa and the modulus elasticity to iron cast is 84 kn /mm2.
7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative image) has 48 teeth on front sprocket (Crank side), the diameter of front sprocket being 10.5 inches. The rear wheel has a cassette with a cluster of 6 sprockets, with number of teeth on Sprocket #1 (lowest gear) to Sprocket # 6 (highest gear) being 30, 26, 23, 20, 16 and 12, respectively. (Ignore wind resistance and friction between machine elements) (a) If the rider is pedaling at a constant 105 rpm with an effective force of 28 lb acting on periphery of front Sprocket (at 5.25 inch radius length, the force location indicated by red arrow), and is engaged in Sprocket #5, what would be the torque acting on Sprocket # 5, and the RPM at which the rear wheel is spinning? (b) For the condition as described in (a), If the diameter of wheels is 26 inches, what is the speed of the bicycle? &
3. Design a roller chain drive. Specify the chain size, the sizes and number of teeth in the sprockets, the number of chain pitches, and the center distance. Problem Driver Driven Input Input Power Nominal Туре Machine speed output (HP) (kW) speed(rpm) (rpm) 500 Roller 250 6-cylinder engine Heavy 40 29.8 Chain Conveyor
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is
4. A pair of spur gears with a centre distance of 495 mm is used for a speed reduction of 4.5:1. The module is 6 mm. Calculate the number of teeth on the pinion and the gear.
A shaft turning 150 RPM is to drive another shaft at 200 RPM. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 2500 FPM. Please provide illustration.
QUESTION 5 A steel gear is to be mounted on a solid steel shaft using an interference fit H6/s4. The gear has 17 teeth cut to a module of m35 mm. The shaft diameter is 52 mm. The gear face width is 50 mm. what is the torque transmission capacity for this mounting? Assume a steel-on-steel friction coefficient of 0.6. The gear does not have protruding hub and it can be treated as a disc the thickness of which is equal to the face width of the gear teeth.Answer in N-m. (Acceptance limits=+/-10%)
A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear will be rotating at a speed of 480 rpm. If the module of the pinion is 2,5 mm and pressure angle is 25 degree; Evaluate the outer diameter (mm) of the gear.
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
A pair of standard 20o full-depth spur gears has a module of 1 mm. The driven gear has 30 teeth. Determine the minimum number of teeth for the pinion so that the contact ratio is greater than 1.6.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
|Q1: Two spure gears are engaged. The large one has Pd=5, D= 10 inch. The speed ratio is (2), ø = 20°. Find the length of line of action and contact ratio.