Problem 6 : (SP10.2) Note: This problem has 3 parts: a, b, and c. Remember to do all three. Determine the output S4...So for the functional logic circuit shown below under the following conditions: A3...Ao = 1001, B3...Bo = 1100 for (a) Sub= 0 and (b) Sub = 1. (c) Explain what this circuit does in one or two sentences. Sub A3 B3 A B Cin C Σ S4 S3 A₂ B₂ A B Cin C Σ S₂ A₁ B₁ A B Cin C. Σ S₁ Ao Bo A B Cin Co Σ So

Problem 6 : (SP10.2) Note: This problem has 3 parts: a, b, and c. Remember to do all three. Determine the output S4...So for the functional logic circuit shown below under the following conditions: A3...Ao = 1001, B3...Bo = 1100 for (a) Sub= 0 and (b) Sub = 1. (c) Explain what this circuit does in one or two sentences. Sub A3 B3 A B Cin C Σ S4 S3 A₂ B₂ A B Cin C Σ S₂ A₁ B₁ A B Cin C. Σ S₁ Ao Bo A B Cin Co Σ So

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Q1) For the circuits shown in figures 1 and 2: 1. What is the function of output? 2. Find the max. and min. Vol. value? 3. Determine the static power (avg.)? 4. Design equivalent logic circuit by CMOC logic circuits? Use VDD= 10 V. Vr.o=1V. Vru-1V. (W/L)o= (5/2), (W/L)L (20/2), RD = 40k, KL = 10P A/V^2 and KO = 40pA/V`2? Figure 1 5 VDD RD Figure 2 बदना दे
A certain digital circuits designed to operate with voltage levels of -0.2Vdc and -3.0Vdc. If H= 1 =-0.2 Vdc and L =0 =-3.0 Vdc, is this positive logic or negative logic ? H=+5.0Vdc. and. L=+1.0Vdc What are the voltage levels between fall and rise times are measured? What is the value of Duty cycle H if the waveform is high for 2 ms and low for 5 ms?
Reduce the logic equation with circuit diagram and draw the simplified circuit.
what are your expectations on this subject Logic Circuit and DESIGN (Digital Electonics) What could you contribute to meet your expectations? Give atleast 5 expectations and contribution on this subject in paragraph form.
(a) Discuss the key characteristics of Unipolar Logic Families and Bipolar Logic Families. What points are important to consider for interfacing the components from different Logic Families.
Sub:Digital Logic Design
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th R₂ = 5600 R₁ = 4700 M3 Ao M₁ M₂ a. Indicate and verify the state of each MOSFET and V for the following input 0 combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. Example: M1 is assumed to be in saturation. If Vgs = 2 V, Vds = 4V, Vds > Vgs - Vth 4>2-1 4> 1 (ok) Vgs > Vth (2>1) A B M1 state M2 state M3 state V OV OV 5 V OV b. What kind of logic circuit is implemented in the circuit above? 5V www. V₂ 0
Up/Down State Machine Cousider a state machine implementation of a two bit up/down counter mput: up/doun, and two outputs: Outo and Out,, which also indicate the next state. When up/dowTI is high, the counter counts up (00,01,10,11,00, ). When up/doun is low, the counter counts down (00,11.10.01.00, ..). The state machine has one Part A Complete the state diagram below by adding all required transition arcs with input annotations. Output annotations are not required since they correspond to the new state. state state 00 01 state state 10 11
Consider a digital logic circuit with two diodes as shownin figure 1. The diodes D1 and D2 are ideal (i.e. Vy = 0). 12 D ov, out 10 D2 5V 50kO Figure 1 A digital logic circuit with two ideal diodes A. Complete the equivalent circuit below and determine the output voltage vout oV and v, = 5V. Verify the conduction states of diodes by finding the current through D, and the voltage across D, when vị = Note that the output voltage is the same when v, = 5V and v, = 0V. 12 D out 12 D2 5V 50k2 Complete the equivalent circuit below and determine the output voltage vout when vị = v2 = В. 5V. 1Ω D Qut 10 5V 50k2 B.
Find the logic value (high / low) of the V0 output obtained for the V1 and V2 inputs in the circuit consisting of NMOS two mosfets. (low: between 0-2.5V; high: between 2.5-5V) The reasons for the reason (high / low) for each case should be specified in filling the table.
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th W R₂ = 5600 PEETHIPPIN R₁ - 4700 M3 M₁ M. 0 a. Indicate and verify the state of each MOSFET and V for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. 오 Ao SV why
DESIGN THE BCD SEVEN SEGMENT LED'S FOR e, f and g. a) Simplification using K-map. b)Give the Boolean expression c) Logic diagram circuits. For e,f and g.