Problem 4.24 The tower crane is used to hoist a 2.1-Mg load upward at constant velocity. The 1.4-Mg jib BD and 0.4-Mg jib BC have centers of mass at G₁ and G2, respectively. (Figure 1) Figure 1 of 1 4 m T 9.5m 136 G₁ Part A Determine the required mass of the counterweight C so that the resultant moment produced by the load and the weight of the tow crane jibs about point A is zero. The center of mass for the counterweight is located at G3. Express your answer to three significant figures and include appropriate units Mc = Submit O μA Value Units My Answers Give Up D ?

Problem 4.24 The tower crane is used to hoist a 2.1-Mg load upward at constant velocity. The 1.4-Mg jib BD and 0.4-Mg jib BC have centers of mass at G₁ and G2, respectively. (Figure 1) Figure 1 of 1 4 m T 9.5m 136 G₁ Part A Determine the required mass of the counterweight C so that the resultant moment produced by the load and the weight of the tow crane jibs about point A is zero. The center of mass for the counterweight is located at G3. Express your answer to three significant figures and include appropriate units Mc = Submit O μA Value Units My Answers Give Up D ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

O "lzain IQ 13/13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN STEEL ROD. Ast3 200 mm2, Aalu=300 mm2 Steel Rod Est= 200 kN/mm? A ST=200 mm? Lst= 4 m Aluminum Rod Ealu= 70 kN/mm? Aalu-300 mm A Lalu= 2 m 4 M 8M 50 kN 149 MPa 223 MPa 15 MPa 44 MPa O لم يتم إنشاء هذا المحتوى ولا اعتماده من قبل Go ogle. - شروط الخدمة - سياسة الخصوصية Google zilai
A 1m RB B 2m C 153 kN/m 2 m D 28 KN 3m 19 kN/m E RE 2 m Question: Compute the shear diagram of the given load diagram F
Q1- A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using Working Stress Method to calculate maximum load (Pmax.) which act at the mid-span of the beam (neglect self-weight), 100 mm 100 mm -537 mm- 40 25 mm 300 mm -ww009 Figure 1 Pmax L=5 m-
QUESTION 5 The equivalent concentrated force of the below distributed load equals: 200N 700 N O 1700 N O B00 N O 900 N
A 5-kip crate is supported by a pulley system and a horizontal force P.a) Find P and the angle α. Report your answer in kips (1 kip = 1000 lbs).b) For this problem if you double the weight of the crate, will the force P double? Briefly explain why or why not.
PROBLEM 1 The pre-cast T-beam has the cross-section shown. Determine its weight per meter length if it is made from reinforced stone concrete and eight 20-mm cold formed steel reinforcing rods. USE : Psteel = 77.5 KN/m³ = 23.5 kN/m³ concrete PROBLEM 1 200mm 1 200mm 500mm 375mm 50mm 375mm
(c) A bridge shown in Figure 6 were imposed with a Uniformly Varying Load (UVL). Replace the UVL with an equivalent resultant force, and also specify its location on the beam measured from point A. Wo Wo A B L 2 L 2 Figure 6
The jib crane shown is subjected to three coplanar forces. Determine the resultant of these forces and specify where the resultant’s libe of action intersects the column AB and the boom BC.
5.The values of Yj and Y2 of the trapezoidal load are Y 1 V 16.67 kN Y 2 4m 13.33 kN a)Yj=8kN/m, YE3KN/m_b)Y¡=10KN/m, Y½=5kN/m c)Y,÷8KN/m, Y½=0 d)none of the previous choices 6.The approximate value of Y1 for the triangular load is Y1 V 13.33 kN a) Yj=15kN/m d)none of the previous choices b)Y,=10 kN/mc)Y,=20 kN/m 4m 6.67 kN 7.The bending stress along the at neutral axis is а) the minimит value b) the maximum value c) zero d) none of the previous choices
Problem #4: Simplify the given problem into a resultant force and couple moment at O. Then, find the distance where a single resultant force is applied from O. 500 kN-m 7.5 m 6 kN/m lim Figure: 04_P150-151 o Pearson Education South Asia Pte Ltd 2013. 4.5 m 15 kN. Please type answer no write by hend.
hi im stuck in this please help me out A wooden beam is loaded by a concentrated load ?P = 5000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that ???LAB = 3000 mm, ???LBC = 2000 mm, ?0B0=10 mm, ?1B1 = 30 mm, and ?H = 240 mm, ℎ0h0=200 mm, ℎ1h1=20 mm, determine the following quantities below: last two sub parts of question didnt fit in so i will type here- theres no question d e) Determine the maximum magnitude of shear force and bending moment, neglecting the sign. The maximum magnitude of internal shear force, positive value: N The maximum magnitude of internal bending moment, positive value: N*mm f) Determine the magnitude of the maximum bending stress in the beam, neglecting the sign. Maximum bending stress, positive value: MPa
PROBLEM 1 The pre-cast T-beam has the cross-section shown. Determine its weight per meter length if it is made from reinforced stone concrete and eight 20-mm cold formed steel reinforcing rods. USE: P steel = 77.5 KN/m³ P concrete = 23.5 kN/m³ ANS. 8.95 kN/m 200mm 200mm 500mm I 375mm 150mm OO OO 150mm 150mm 375mm