Problem 4: Metal sheet paper is cut to a width of 205 cm with a tolerance of +/-05. The cutting process is centered at 205 and has a standard deviation of 0.4. If we want to eliminate scrap, what should the process center be changed to?

Problem 4: Metal sheet paper is cut to a width of 205 cm with a tolerance of +/-05. The cutting process is centered at 205 and has a standard deviation of 0.4. If we want to eliminate scrap, what should the process center be changed to?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 1RQ: Information such as tolerances and scale can be found in the________ of an engineering drawing.

See similar textbooks

Related questions

Q: In the figure below, explain the case where the dimension tolerance is satisfied, but the plane…

Q: The discrimination of a steel rule scale is determined by the spacing between each graduation…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: If you were to multiply each value in a data set by 6, what effect would this have on data set's…

A: The correct option is C. The standard deviation would also be multiplied by 6.

Q: what is gross error? how to eliminate it gross errors?

A: Gross error:The error caused due to the shear carelessness of an observer in called gross error.…

Q: A constant boundary generated by the collective effects of the MMC limit of size of a feature of…

A: Given data: A condition boundary generated by the collective effects of the MMC limit of size of a…

Q: A component has a strength which is normally distributed with a mean of 6000N and a standard…

Q: 15.4 A schematic representation of basic size and its deviations are given in Fig. 15.20. Identify…

A: In Manufacturing Technology, Limits, Fits, and tolerancing are very important. It gives the…

Q: QUESTION 2 A batch of steel rods has mean tensile yield strength of S=80 ksi. (1 ksi = 1000 psi)…

A: Dear student please rate me postive:) Stay safe stay happy ! Answer-(i) Mean load P = 55 kip…

Q: Describe errors which might occur during the use of the external standards calibration method and…

Q: A part is to be chosen from a sample of 1000 pieces which have a mean tensile strength of 80kPa and…

A: Write the given data. Smax=85 kPaSmean=80 kPaSD=8.5 kPaN=1000

Q: Some engineering components have a mean length of 20 mm and a standard deviation of 0.25mm. Assume…

A: Given data: Mean x-=20 mm Standard deviation σ=0.25 mm In a batch the…

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm, according to…

Q: 4. The number of flaws in bolts of cloth in textile manufacturing is assumed to be Poisson…

A: Please refer the next page for answer

Q: 29. If two planar surfaces are apart from each other by a dimension with a tolerance of t 0.0.05,…

Q: Find the values of mean, median, variance and standard deviation.

A: To find mean, median, variance andstandard deviation.

Q: A shaft has a dimension 025 -C.25 mm. The fundamental deviation and tolerance are respectively -…

Q: (a) Figure 1 shows surface roughness and tolerances obtained in Chemical Machining (CM) and…

A: Chemical machining and electrochemical machining

Q: One step in the manufacture of a certain metal clamp involves the drilling of four holes. In a…

A: AS PER COMPANY GUIDELINES, ONLY 3 SUBPART CAN BE SOLVED AT A POST. KINDLY REPOST THE OTHER QUESTIONS…

Q: A cold cereal manufacturer wants 1.5% of the product to be below the weight specification of 0.567…

A: given; ⇒Z=1.5%=0.015⇒weight(x1)=0.567kg⇒standar deviation(σ)=0.018kg⇒mean(x2)=?

Q: III in the blanks: vending machine automatically pours soft drinks into cups. The amount of soft…

Q: 2310. mm as the Iimits for afts. The natural tolerance is found to be a -distributed random variable…

A: Given that ,μ=25mmXo=25.05mmR=98%

Q: The design specification on the part is that the diameter = 45.000 ± 0.150 mm. (a) What proportion…

A: The design specification is an important aspect of manufacturing. It provides the limits within each…

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅6 mm, according to the…

A: Given Data Nominal diameter of rod is : d=6 mm Upper deviation is : es=-40.64 mkm=-0.04064 Lower…

Q: Example 10: An engineering in PVC pipe factory wishes to select a pipe bearing pressure in the…

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: () Draw the project network. (i) Find the expected duration and variance for each activity. (ii)…

Q: Unilateral tolerance is one in which the variation from the specified dimension is permitted in only…

A: Unilateral tolerance is one in which the variation from the specified dimension is permitted in…

Q: Transcribed image text: Q 1/ The basic size of two comparable parts with the tolerance code for each…

Q: outline the foundamental difference between errors that can be largely eliminateed and errors that…

A: Error- The difference between the true value and the measured value is called error. Errors are not…

Q: Measurements of 10 min each give gross and background count rates, respectively, of 72 and 54 cpm,…

A: Given data: Time taken = t = 10 min Gross count rate = G = 72 cpm Background count rate = B = 54 cpm…

Q: 241.5 241.2 241.0- 240.5- 240.0- 240 239.5 239.0- 238.8 10 12 14 16 18 20 2 24 26 Hour What is the…

A: The standard deviation of the line graph is, total main points on the graph…

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅50 mm, according to…

A: Note:- In this solution “mkm” is taken as a micrometre. Given data: The diameter ϕ50 lie in between…

Q: 1 To determine the limit deviations, limit of sizes, fit type, limit clearances or interferences and…

A: Calculated the limit deviations, limit of sizes, fit type, limit clearances or interferences and…

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅6 mm, according to the…

A: Rod, ∅47g6 (1) Basic size of rod is 47 mm (2) Tolerance value of rod is the value of IT6 D =…

Q: Problem 24.17 A mechanical component is subjected to a mean stress of 100 N/mm and a standard…

A: Given: Mean stress: S_=130 N/mm2σ_=100 N/mm2SSD=15 N/mm2σSD=10 N/mm2 We need to find the margin of…

Q: In the SPT test performed at the point where a single foundation of 1.5 m * 3.0 m will be located,…

A: Given: 1.5*3.0 m N=5 Df= 0 m Settlement, S=25 mm

Q: a) The elongation of a steel bar under a particular load has been established to be normally…

A: (a) Given, Mean, μ=0.05 in Standard deviation, σ=0.01 in

Q: The smallest deviation of a ruler is 1 cm. This quality of the instrument is denoted by. • It…

A: The smallest unit which can be measured is known as the least count of the ruler. When we measure…

Q: If there are 10 values each equal to 10. Then standard Deviation of these values is (a) 100 (b) 20…

Q: What is called the upper limit deviation es and by what formula is it calculated?

Q: A critical part has a manufacturing specification of 4.5 cm ± 0.10. If this measurement is larger…

A: Taguchi loss function follows the form L(x) = k (x - T)2where L(x) is the Taguchi Loss Function…

Q: If the standard deviation of a nut's hole diameter exceeds 0.01 millimeters, there is an…

A: according to given details

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅44 mm (nominal size),…

A: In industry it is impossible to manufacture a product with exact dimension. Due to this some…

Q: The analysis of a proposed design for a component revealed a state of tensile stress with a mean…

A: Given, Mean value of tensile stress is σmean=25000 psi Standard deviation stress is σamplitude=5000…

Q: Suppose scores on an IQ test are normally distributed. If the test has a mean of 100 and a standard…

Question

Problem 4: Metal sheet paper is cut to a width of 20.5 cm with a tolerance of +/-0.5. The cutting process is centered at 20.5 and has a
standard deviation of 0.4. If we want to eliminate scrap, what should the process center be changed to?
B
I

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

Indicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle cylinder is Odh7, use Envelope requirement; b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od is $0.012mm; c) Total run-out tolerance of right end surfaces related to axis of Pd is 0.01 mm; d) The surface of od cylinder is obtained by the method of removing material, and the maximum allowable value of Rz is 0.4µm. All surfaces are obtained by the method of removing material, and all the roughness Ra allowable value is 6.4 pm.
The nominal size of a hole is Dn = 230 mm. The lower limit deviation El = -0.016 mm, and %3D %3D ww the tolerance TD = 0.026 mm. What is the upper deviation ES? %3D 1) ES = +0.010 2) ES = +0.042 3) ES = +0.026 4) ES = -0.010.
1. Whatis the philosophy of the Goand No-Gogauging? 2. Complete any missing information on part 1&2 and in feature control 1 &2 (assume any tolerance). 3. Add all information needed for Gage 1& 2 (show calculation)*** Part 1 Part 2 Ø1.005t908 Ø1.000+ 000 -.005 Ø.500* n+.000 -.005 Ø.505+.005 000 Gage 1 Gage 2
Can you solve the problem again by taking the scale factor 13 ? Can you also draw the graphs requested in the question in the excel program?
how do you write this in a feature control frame? "The cross-sectional shape of this feature must be round within a radial tolerance zone of .002"
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
2There are two different indicated drawings in Fig.1. (1) Judge the tolerance principle they used respectively; (2) Calculate their allowed perpendicularity tolerance in MMS respectively; (3) Calculate their allowed perpendicularity tolerance in LMS respectively (4) If the actual size is 17.9 mm, the actual perpendicularity error is 00.009mm, judge whether it is qualified according to Fig.1 (a) or Fig.1 (b) respectively. ( ¢18 8 00.01 (M) A 0.1 -0.1 I ø0.01 |4 (a) (b)
Whats the formulae for temperature error %
Calculate the maximum limit if the tolerance is 0.004 cm and the minimum limit is 0.985 cm.
There are some incorrect indications in the following Fig.2. a) Re-draw a correct indicated drawing on the answer sheet. b) Describe the tolerance requirements of the corrected drawing. 0.01 7 0.01 B I0.01 B 60h 7 o.015 A
1. Calculate the tolerances and allowances for a shaft with a diameter of 40 mm with a tolerance area k and a tolerance quality number 6, paired with a hole of the same diameter as the shaft and a tolerance area H with a tolerance quality 7. Also draw these tolerances schematically. ( answer in 20 minutes very needed thank u )
Information such as tolerances and scale can be found in the________ of an engineering drawing.