Please don't provide handwritten solution ..... Problem 3)Assume that at the instant the 60 mA dccurrent source is applied to the circuit inFigure P3, the initial current in the inductoris -45 mA, and the initial voltage on thecapacitor is 15 V (positive at the upperterminal). Find the expression for i, (t) for120 if R equals 200 £2.60 mAOiL(1) 50 mH0.2 μF R

The given circuit is shown below.The value of resistance is .Initial conditions are Volts…

Answered: Problem 3) Assume that at the instant…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
The figure below shows a simple RC circuit with a 3.30-μF capacitor, a 4.40-M resistor, a 9.00-V emf, and a switch. What are the following exactly 9.00 s after the switch is closed? (a) the charge on the capacitor 13.7204 UC (b) the current in the resistor 0.0110522 x Your response is off by a multiple of ten. HA (c) the rate at which the capacitor is storing energy μW (d) the rate at which the battery is delivering energy μW
For the circuit below assuming an ideal switch, preform transient analysis to predict the voltage across resistor, R2 and plot the results. The inductor will have zero current as initial condition. L1 0.005 2 U1 100mH R1 1k V1 20Vdc R2 100
Make a clamper circuit using 500 µF capacitor, silicon diode, and a 100 KΩ resistor connected to a 10 Vpeak sine wave. Draw the output waveform and indicate the amplitude and the time values supported by your solutions. Do these for both positive and negative clamper circuit. Show your circuits first before your solutions and waveforms.
1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?
When the switch is in position 1, the circuit will charge the capacitor. Find the Thevenin Equivalent Circuit for the charge phase and determine the time constant (Rh*C) for the charge phase.
The following figure represents an RC-Circuit with the switch. In Figure A, the capacitor is initially uncharged. In Figure B, the capacitor is initially fully charged. 1) Draw and label the current direction immediately after the switch is closed for each figure. 2) Consider Figure A. What is the voltage across the capacitor as t → 0? Explain. 3) Consider Figure B. Is the voltage across the resistor increasing, decreasing or staying the same as t → 0? Explain. A) B) R C
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
3. For the R-C circuit in below figure, composed of standard values: a. Determine the time constant of the circuit when the switch is thrown into position 1. b. Find the mathematical expression for the voltage across the capacitor and the current after the switch is thrown into position 1. c. Determine the voltage Vc and current éc the instant the switch is thrown into position 2, t-1s. d. Determine the mathematical equation for voltage Ve and current zc for the discharge phase. R=4.7KO, C=56µF, E=22V + 'R 29 ve (a)
Basic Electrical Engineering: Inductance and Capacitance You are an electrician working in an industrial plant. You discover the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-V AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 µF and a voltage rating of 240 V AC. The only 10-µF capacitor in the storeroom is marked with a voltage rating 350 VDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are an electrician working in an industrial plant. You discover the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-V AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 μF and a voltage rating of 240 V AC. The only 10-μF capacitor in the storeroom is marked with a voltage rating 350 VDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
For the circuit at right: a. Immediately after the switch is closed, what is the current in the inductor? 12V b. A long time later, what is the current through the inductor? c. What is the energy stored in the inductor in part (b)? d. A long time later, the switch is opened. Immediately after, what is the voltage across the inductor?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS