PROBLEM 3 A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm. When the tensile load P reaches a value of 20kN, the distance between the gage marks has increased by 0.122 mm. What is the modulus of elasticity? Note: Please show complete solution with FBD

PROBLEM 3 A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm. When the tensile load P reaches a value of 20kN, the distance between the gage marks has increased by 0.122 mm. What is the modulus of elasticity? Note: Please show complete solution with FBD

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Related questions

Q: 65. In some cases of repairs of girders damaged by collision, the damage is severe what is used? A. ...

A: Connections and dowels are utilized sometimes of fixes of supports harmed by impact when the harm is...

Q: The rectangular coordinates of a particle which moves with a curvilinear motion are given by x = (10...

Q: nner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear the tube when the c...

A: According to given data

Q: Determine whether the D = 560 kips L = 68 kips compression member shown is adequate to support the g...

Q: 1. The roof deck of the single storey building is subjected to a dead load plus live load of 6kN/m²....

A: We have to determine the distributed loading that acts along the purlin DF, and the loadings that ac...

Q: rength (OMn). Does the beam satisfy ent? Given: f'.= 6.000 psi, A. = 4 #10

A: tensile force = compression force AS. fy =0.85 fc' . Ac 460 = 0.85 5. Ac Ac = 56.47 in2 depth of ...

Q: For the truss shown, determine the axial force acting on member BC 5 kN 4 kN 3 kN 2 kN 3 m 3 m 3 m 3...

Q: M= 100 KN.m 300 KN/m 1.0 m 1.0 m 1.0 m 3.0 m R1 R2

Q: b). The T-beam in part (a) is 6 m long, is supported on both sides in such a way that each support i...

A: (b) The given diagram is shown below, To find the value of x

Q: 2 k/ft -15 ft 6 ft- El = constant E = 29,000 ksi

A: Solution: E=29000 ksi I =3500 in4 Step 1: To find the reactions at A and B: VA + VB =2x15 + 2x6 VA +...

Q: Determine the forces in members AE, BF, and CF of the truss, and state if the members are in tension...

Q: 1)A bar has an original diameter of 0.5 in. and length of 9 in. a) Determine modulus of elasticity i...

Q: Determine static indeterminacy of truss structure

A: Given data in question Truss To find out Indeterminacy Note Ds= degree of static indeterminacy m...

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress d...

A: This question is related to the Strength of material. In this question we calculate axial stress and...

Q: A projectile is launched from a cliff 100 meters above level ground with a launch velocity of 20 m/s...

Q: Consider the following figure. h B III (a) Determine the maximum tensile stress o, and maximum compr...

Q: Determine Base period=88 days Duty=320 ha/cumec

Q: (1) Determine an equivalent pipe for the system shown below. (2) If Qr = 2.6 cfs, compute (a) the to...

Q: W, = 8kN/m W, = 5kN/m 2.4m 3.6m 6.0m

Q: A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water ...

Q: Classify the structure shown in the figure. OA. Indeterminate. 21st degree O B. Indeterminate, 24th ...

Q: AP 35° 35°

Q: (b) A portal frame ABCD is fixed at A and hinged at D. Draw the bending moment diagram due to a poin...

A: Moment distribution method: The moment distribution method is used to analyse the indeterminate beam...

Q: AREA-MOMENT METHOD 40 kn 28.0 kn/m 10 kN/m DRAW THE MOMENT DIAGRAM BY PARTS WITH COMPLETE SOLUTION 3...

Q: 41. Which of the below is a pigment imparting brown colour? A. O Raw Sienna B. O Soot C. O Burnt Sie...

A: Answer : option ( C ) Burnt Sienna is correct option . More explanation is given in next step.

Q: Two 20 x 100-mm and two 20 × 180-mm boards are glued together as shown to form a 120 x 200-mm box be...

Q: B. A reversed curve of equal radii connects two parallel tangents 15 m apart the length of chord fro...

A: Please refer the attached image for complete solution. THANK YOU !

Q: What is the Maximum moment in kN-m. Given: w1 = 44, w2 = 19, a = 3, b = 2, and c = 3. w1 kN/m w2 kN/...

Q: Determine Base period=88 days Duty=320 ha/cumec

A: To find : Delta

Q: A layer of clay of 6.5 m thickness is located between two sand layers. The coefficient of consolidat...

A: This question is related to the Consolidation from soil mechanics.

Q: A study showed that during the peak-hour commute on two routes connecting a suburb with a large city...

A: There are a total of 5500 vehicles that make the trip. 1) Route 1 : 7 miles long with a 65-mi/h spe...

Q: 69. In method 3 the restoration is done by addition of. A. O Metal sleeve jacket B. O Aluminium jack...

A: Answer:- A Explaination: Metal sleeve jacket is added in the method 3 to do the process of restorati...

Q: Horizontal stiffness coefficient, K,1 of bar AB is given by 45°B K11 AE, L

Q: reversed curve of equal radii connects two parallel tangents 15 m apart the length of cord from PC t...

Q: B. A reversed curve of equal radii connects two parallel tangents 15 m apart the length of chord fro...

A: This question is related to Curve from Surveying Engineering. In this question we calculate radius o...

Q: kN Situation 2. Determine the value of the plastic load w, (inJusing the concept of collapse m mecha...

Q: Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area ...

Q: 10. Determine the force in members CD, HI, and CJ of the truss, and state if the members are in tens...

Q: 9. In order to find the difference in elevation between two points P and Q, a level was set upon the...

A: Given data in question Line PQ Distances Rod readings To find out Corrected elevation difference ...

Q: A soil specimen weighs 30 grams oven dried. When mixed with 7.50 cc of water, the soil is at its pla...

Q: Problem #5: Plot the shear and bending moment diagrams for the compound beam shown. Supports A and D...

Q: Problem 1. Determine the following unknowns on the beam shown below using Double Integration Method....

A: Given Beam condition From Equilibrium equations ∑FY=0 RA+RD=36×7+39+22+02×6=357kN ∑MZ=0 taking mom...

Q: A child pulls a sled upon snow covered hill. The child does 450 J of work on the sled. If child walk...

A: Given data : The value of Work done by child W=450 J The value of displacement d=12 m In this ques...

Q: he elements of a reverse curve are as follows: I1 = 18.5˚ I2 = 23.7˚ D1 = 2.6˚ D2 = 4.4˚ If...

A: Given:- I1 = 18.5˚ I2 = 23.7˚ D1 = 2.6˚ D2 = 4.4˚ STA PT = 26+513 To find:- STA PI1

Q: Determine static indeterminacy of truss structure

Q: 1)A bar has an original diameter of 0.5 in. and length of 9 in. Ain a) Determine modulus of elastici...

Q: Determine Base period=88 days Duty=320 ha/cumec

A: B = 88 days D = 320 ha/cumec We know that delta ∆ = 8.64 (B/D) Where B is in days and D is in ha/...

Q: H.W: In the pipe systems show, find the distribution of flow, with a friction factor of 0.0163. Assu...

A: Given data: Friction factor (f) =0.0163 P at first point-1000kPa Pressure at Point A-? Pipe L ...

Q: Determine the outside diameter of a hollow steel rod that will carry a tensile load of 55,000 kg at ...

A: Given data:Tensile load, P=55000 kgσ=1500 kg/cm2t=10 mm=1 cm

Q: 5. The corrosion of reinforcement due to extreme exposure is common for structure located in

A: To find: The erosion of support because of outrageous openness is normal for structure situated in

Question

PROBLEM 3
A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm. When the tensile load P reaches a value of 20kN, the distance between the gage marks has increased by 0.122 mm. What is the modulus of elasticity?

Note: Please show complete solution with FBD

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A tensile test is performed on a brass specimen 10mm in diameter using a gage lenght of 50mm. When the tensile load P reachers a value of 20kN, the distance between the gage marks has increased by 0.122 mm. What is the modulus of elasticity of the brass.
Please present FBD/s A tensile test is performed on a brass specimen 10mm in diameter using a gage lenght of 50mm. When the tensile load P reaches a valule of 20kN, the distance between the gage marks has increased by 0.122mm. What is the modulus of elasticitiy of the brass?
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P- 30 kN. Knowing that E- 70 GPa, and the change in diameter of the rod- 0.00955 mm, determine the poissons' ratio v. 20n diateter gage length-150 0.33 O 0.6 0.29 O 0.35
PROBLEM 3 A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm When the tensile load P reaches a value cf 20KN, the distance between the gage marks has increasedby 0.122 mm What is the modulus of elasticity of the brass?
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1/2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elonga- tion was 4.66 x 10-3 inches. If the load is assumed to be within the linear elastic range of the material, determine the modulus of elasticity.
A steel specimen is tested in tension. The specimen is 1 in. wide by 0.5 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 36 kips and fractured at 48 kips.a. Determine the tensile stress at yield and at fracture.b. If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
160 Upper scale A tensile test specimen of stainless steel alloy having a diameter of 0.550 in. and a gage length of 2.5 in. was tested to fracture. Stress and strain data obtained during 120 80 Lower scale the test are shown in the Figure Determine: (a) the modulus of elasticity. (b) the proportional limit. (c) the ultimate strength. (d) the yield strength (0.20% offset). (e) the fracture stress. 40 0.020 0.002 0.100 0.120 0.010 0.012 0.0 0.040 0.004 0.060 0.006 0.080 0.008 0.0 Strain (in./in.) Stress (ksi)
A steel specimen is tested in tension. The specimen is 2 in. wide by 2.3 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 30 kips and fractured at 40 kips. a) Determine the tensile stress at yield and fracture; b) If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 2 the yield stress.