Problem 3: A cylindrical tank with an outer diameter of 1.2 m will be pressurized to 3 MPa internal pressure. The tank will be made of steel (Sy = 300 MPa). (a) What is the minimum wall thickness of the tank to guarantee a safety factor of 2.5 against yielding? Use the maximum shear stress criterion. -- P.3MP Stel Sy²3. B tmin would be:

Problem 3: A cylindrical tank with an outer diameter of 1.2 m will be pressurized to 3 MPa internal pressure. The tank will be made of steel (Sy = 300 MPa). (a) What is the minimum wall thickness of the tank to guarantee a safety factor of 2.5 against yielding? Use the maximum shear stress criterion. -- P.3MP Stel Sy²3. B tmin would be:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

A closed thin walled cylindrical vessel has a diameter D of 470 mm, a wall thickness t, and length L of 500 mm. It is subject to an internal pressure P of 0.16 MPa. Calculate the minimum wall thickness of the vessel if it has a limiting stress of 5 MPa. Give your answer in mm to 3 significant figures. de 00 $ de
A closed thin walled cylindrical vessel has a diameter D of 780 mm, a wall thickness t of 3.5 mm and length L of 950 mm. It is subject to an internal pressure P of 50.0 MPa. Assuming that Youngs modulus is 200 GN/m² and Poisson's ratio is 0.3, calculate the change in length of the vessel due to the internal pressure. Give your answer in mm to 3 significant figures. 00 P D 00 $ de OL 4
The wall thickness of a 900mm diameter spherical tank is 22 mm thick. If the stress is limited to 350 MPa, the allowable internal pressure
A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response: 8.16 m 3.68 m 07.36 m 4.08 m
Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. Thechanges in dimension caused by an increase in temperature of 80°C for the:1. Outside diameter 2. Inside diameter 3. LengthNote: All answer must be round off up to 3 decimal places.
A cylindrical tank of 15 m high and 5 m in diameter is to be filled with water. Find the minimum thickness of the tank plating if the ultimate stress is limited to 500 MPa and the factor of safety is 2.
Q 5 A vertical axis circular cylindrical water storage tank of cross-sectional area A is filled to a depth of 15 m. The tank is 4 m in radius and is made of steel having a yield point of 240 MPa. If a safety factor of 2 is applied,determine the required tank wall thickness.. [Use ywater = 9800 N/m³]
Q3: (a) describe the location and function of the following: \i. Gudgeon pin ii. Rod shank ii.Large end (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa.Calculate the tangential stress in the steel.
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Find the longitudinal stress in the tank.
A closed thin walled cylindrical vessel has a diameter D of 290 mm, a wall thickness t of 5 mm and length L of 210 mm. It is subject to an internal pressure P of 18 MPa causing circumferential stress and longitudinal stress in the vessel. Calculate the longitudinal stress due to the internal pressure. Give your answer in MPa to 3 significant figures. 00 P D 60 de OL
a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the maximum pressure inside the tank is 2.0Mpa. Based on the tresca( maximum shear stress criterion) what is the required yield stress of the steel. Please show all work and formulas