How do I solve this question. Problem 10Water flows steadily from an open tank as shownbelow. The elevation of point 1 is 10.0 m, andthe elevation of points 2 and 3 is 2.00 m. Thecross-sectional area at point 2 is 0.0480 m2; atpoint 3 it is 0.0160 m². The area of the tank isvery large compared with the cross-sectional areaof the pipe. Assuming that Bernoulli's equationapplies, compute (a) the discharge rate in cubicmeters per second and (b) the gauge pressure atpoint 2.10.0 m2 32.00 m

Given data: The elevation of point 1 is 10.0 m The elevation of points 2 and 3 is 2.00 m The…

Problem 10 Water flows steadily from an open tank as shown below. The elevation of point 1 is 10.0 m, and the elevation of points 2 and 3 is 2.00 m. The cross-sectional area at point 2 is 0.0480 m²; at point 3 it is 0.0160 m². The area of the tank is very large compared with the cross-sectional area of the pipe. Assuming that Bernoulli's equation applies, compute (a) the discharge rate in cubic meters per second and (b) the gauge pressure at point 2.

Problem 10 Water flows steadily from an open tank as shown below. The elevation of point 1 is 10.0 m, and the elevation of points 2 and 3 is 2.00 m. The cross-sectional area at point 2 is 0.0480 m²; at point 3 it is 0.0160 m². The area of the tank is very large compared with the cross-sectional area of the pipe. Assuming that Bernoulli's equation applies, compute (a) the discharge rate in cubic meters per second and (b) the gauge pressure at point 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
Water flows steadily through a pipe with ID 35 mm. This pipe expands suddenly to an inner diameter of 75 mm and then stays at that diameter. The flow speed in the 35 mm pipe is 32 m/s. The water gage pressure in the thinner pipe is 510 kPa. 1. What is the pressure at the entrance to the thicker section of the pipe? Is the pressure there larger or smaller than in the thin pipe section?
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 m/s. The difference in elevation between the two water levels in the piezometers is 3 cm. The water temperature is 10oC. What is the velocity (m/s) at the minimum area?
Gentlemen, please check and help me with question #3 Tank filled with water and orifice diameter of 3 cm in the bottom. Height between centre of orifice and water level 3 m. Coefficient of discharge - 0.64, coefficient of velocity- 0.97. Find: 1. Actual jet velocity? This one I know how to do. V(actual) = square root from 2gH 2. Jet diameter? This one I know as well. Coefficient of contraction= coefficient of discharge/ coefficient of velocity Diam of jet we will find from formula: Coefficient of contraction = (diameter of jet/diameter of orifice)^2 3. How long will it take for jet to be established?
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
Water is to be pumped from a lake to a ranger station on the side of a mountain (see figure). The length of pipe immersed in the lake is negligible compared to the length from the lake surface to the discharge point. The flow rate is to be 95.0 gal/min, and the flow channel is a standard 1-inch. Schedule 40 steel pipe (ID = 1.049 inch). A pump capable of delivering 8 hp (= W, ) is available. The friction loss F (ft-lbf/lbm) equals 0.0410 L, where L (ft) is the length of the pipe. %3D
The Reynold’s number for fluid in a pipe of 10-in diameter is 2000. What will the Reynold’s number in a 6-in diameter pipe forming an extension of the 10-in pipe? Take the flow as incompressible.
Inflow depth= h, hwater Water from a storm drain flows over an outfall with a height, h, = 0.25 m, and width into the paper of B = 5.0 m. The inflow has a velocity, Uin = 2.0 m/s, into a tank. You can assume that the water instantly spreads out over the surface in a smooth fashion so that the water level in the tank can be considered a flat surface of area A=BxL. At the bottom of the tank is a porous bed that absorbs the water at a uniform vertical velocity of V = 14.0 mm/s, as shown in the figure given below. The outflow at the bottom of the tank, Qout m³/s is equal the volume flux of water entering the filtration layer. The tank is B = 5.0 m deep into the paper and has a length L = 25.0 m. There is an initial depth of water on top of the porous bed of ho =29.0 mm. Find the height of the water, h,water (the ponding level) above the porous media at t = 11.0 seconds after the start of the storm. Please provide your answers to 5 significant figures. h = m
A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters), (provide your answer with four decimal points) P Type here to search O 10°C Sunny AQA ENG 0029 16/02/2022 DELL priSc FS F6 5 E R J K L %23 F E Aock C V sage page VO at gr ctri