Problem 1 Convert 230 kPa to millimeters of mercury, inches of mercury, and feet of water. Problem 2 A manometer connects an oil pipeline and a water pipeline as shown in Fig. 2.4. Determine the difference in pressure between the two pipelines using the readings on the manometer. Use Sal = 0.86 4 S =13.6. Air Water cm 6 cm 4 cm Mercury Oil 上

Problem 1 Convert 230 kPa to millimeters of mercury, inches of mercury, and feet of water. Problem 2 A manometer connects an oil pipeline and a water pipeline as shown in Fig. 2.4. Determine the difference in pressure between the two pipelines using the readings on the manometer. Use Sal = 0.86 4 S =13.6. Air Water cm 6 cm 4 cm Mercury Oil 上

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 15P

See similar textbooks

Similar questions

A pipe contains an oil sp.gr. 0.80. A differential manometer connected at the two points A and B of the pipe shows a difference of mercury as 20 cm. Find the difference of pressure between the two points
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined inan internal reservoir inside the closed tank, the height of mercury is 450mm. An openmanometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , thedeflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y.b) Pressure at point B in kPa. c) Pressure at point C in psi.
A pipe contains an oil of specific gravity 0.9. A Differential manometer Connected at the two points A and B shows a difference in mercury level as 15 cm. Find the difference of pressure at two points.
For the shown inverted manometer, all fluids are at 20°C. If P3 - PA = 130 kPa, what must the height y be? B Meriam red oil SG = 0.83 0.25 m Water y Mercury A SG = 13.6 0.4 m В
A mercury manometer is connected to a flow meter in a pipeline. The gaugepressure at Point 1 is 38 kN/m2 and at Point 2 the vacuum pressure is −50 kN/m2. The fluid in the pipeline is water. Calculate the manometer reading Rp .
A manometer is attached to a conduit as shown. What is the pressure at A in KPa given the following: Sp.gr. of liquid B = 10 h = 150 mm d = 450 mm Water |h=150 d=450 B (sp. gr. = 10)
A docs.google.com/forms/d/e/1FAlpQLSetk8UE/ PROBLEM 6: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3 * Oil SG = 0.79 P gage = 260 kPa Gasoline SG= 0.70 Pipe Air 45 cm 50 cm 22 cm 10 cm Mercury SG= 13.6 Water Your answer
Problem 1. A U-tube manometer is connected (at the bottom portion) of a barrel in a form of frustum of a cone 1 meter high with a diameter at top 0.20m and its diameter at the bottom is 0.12m. When the barrel is empty the water surface is at point A and the manometric fluid mercury shows a deflection of 18 cm. a. Determine the new deflection of mercury in mm when the barrel is 2/3 full of water 18 cm b. Determine the new deflection of mercury in mm when the barrel is full of water (
Question 1 5 Marks The air-oil-water system shown below is at 21°C. Gauge A reads 11 kPa and gauge B reads 14 kPa less than Gauge C. (a) Calculate the density of the oil. (3 marks) (b) What is the reading of Gauge C? (2 marks) air oil water 1 m 0.65 m 0.65 m 1 m Ø A Ø B
(c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, d is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. i) Calculate the volume flowrate of oil inside the conduit. ii) Determine the mass flowrate of oil inside the conduit. iii) Explain why the discharge coefficient Ca, for the ventury meter is higher compared to the nozzle meter. 2(P – P.) V. ventury AP oil d Figure 5
The air exits the nozzle to the atmosphere and enters a vertical plate as shown in the figure. it crashes. The horizontal force required to hold the plate that way is 9 N. Pressure Determine the pressure read on the gauge. Explain under what assumptions a solution can be made. (A1=0,01m2, A2=0,003m2)