Answered: Problem 09.037 - Admittance of a…

Problem 09.037 - Admittance of a parallel combination of R, L and C Determine the admittance Y for the circuit given in the figure. Take R = 4 Q. Y R The admittance Yis j8 Ω +j :-j10 S2 )) ms.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: O O Which of the following metal is the best magnetic material? gold Tin aluminum Iron

A: The magnetic material is used in transformer core. The magnetic material should attract toward…

Q: 8 кл 1кл скл покл 8 MA + Vc(4) HE 470uF 5 кл 3кл вто 12V

Q: For Wheatstone bridge circuit, the following values are given. Vsupply=120V; R₁ = 15 №; R₂ =30Ω; R3…

A: When R1 will get disconnected then this will not work as balanced wheatstone bridge. So we will…

Q: Find the expression for the v(t) and current i(t) of the capacitor as a function of time for the…

Q: For transformer which has, N₁=1000, N₂-250, V₁=120V and RLoad of 120. • What is the value of…

A: Transformer is static device. It can be step up or step down transformer. It has laminated core…

Q: Af the interconnection in Fig. P2.9 is valid, find the total power developed in the circuit. If the…

A: The continous flow of electron constitute current. The current through series elements are equal.…

Q: circuit consisting of three resistors rated: 10 ohms, 15 ohms and 20 ohms are connected in delta.…

A: We need to convert the given delta to star .

Q: need a reference about Elemental Semiconductor

A: Semiconductor has a electrical properties and which is used for the devices like diodes, transistors…

Q: (b) A periodic signal is given in Figure Q1(b). Show that the exponential Fourier Series for the…

Q: Draw or Create a circuit with at least three capacitors, three inductors, and five resistors. (put…

A: Note Only active power will be available in purely R Load Only Reactive power will be available in…

Q: Question 1. A series circuit with a 12V battery is connect to one lamp with resistance 3 ohms, how…

A: Given data, Supply voltage V = 12 V. Resistance R=3 Ω. Time is given t=2 minute = 2×60=120 sec.

Q: 1. (a) The input voltage, v-(t)=20 sin(500m) V is connected to a silicon diade, with Vr=0.7 V in the…

A: To determine the output voltages of the given below circuits:

Q: 14 Perform the following calculation a) 1 245° b) √22-135° c) 1 20° d) √2 245° e) None of the above.…

Q: Problem 06.049 - Series and parallel combination of inductors Find the equivalent inductance of the…

A: We need to find out the equivalent inductance for given circuit.

Q: A 400 V, 3 phase, 50 Hz, Induction motor gives out an mechanical output of 13.586 HP (Metric). It…

Q: Determine the critical frequency value of an HF signal if its maximum usable frequency is 7050.50…

A: Critical frequency Antennas are used to transmit and receive radio frequency waves. The radio…

Q: A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase half-wave SCR…

Q: 3. Use NORTON'S THEOREM to find the Norton's Short Circuit Current, Looking Back Resistance, and the…

Q: iv. V. vi. How much power is the generator now supplying? How much power is supplied to the…

A: The phrase "power generation" refers to the process of producing electricity utilizing various forms…

Q: The plant capacity of a three phase generating station consists of two 15,000 kVA generators of…

Q: If a 25μH inductor is connected to a voltage shown in the figure below: The current through the…

A: The mathematical expression of the given waveform can be obtained by using the line equation and…

Q: 2. Which type of multiplexing can not be used for Analog signalling? a) FDM b) TDM c) WDM d) None 3.…

A: The given problem is from communication system. The detailed solution is given in the next step

Q: Circuit connected in parallel with given values of Vsupply=120V; R₁ = 2 kſ, R₂ = 4KS, R3 =6KQ; R4 =…

Q: 2. Please find Vo in the OpAmp circuit below: + 2 V R2 1 ΚΩ ww (+ · 1 ΚΩ 1 V + OpAmp R3 2 ΚΩ + Vo

A: The given problem is from operational amplifier. The detailed solution is given in the next step

Q: An industrial load can be supplied from the following alternative tariffs : (i) High voltage supply…

A: Voltage: The potential difference in charge between two sites in an electrical field is quantified…

Q: Problem 5. For the following transfer function of the plant and differential equations, derive the…

A: it is asked to find the state space representation of given transfer functions and differential…

Q: Required information Consider the oscillator circuit given below, where L = 0.1 mH and R= 68 kN. 20…

A: Oscillator An oscillator is a circuit that generates a continuous, repeated, alternating waveform in…

Q: What is the ERP if the output of transmitter is 50 kW, the coax line loss is 300 W, and the antenna…

A: The given problem is from antenna theory. The detailed solution is given in the next step

Q: OO Which of the following material is not considered a semi-conductor? Silicon germanium carbon…

Q: Show the connection of a three-stage amplifier with gains of +10, -18, and -27. Use a 270-kΩ…

A: We need to design the circuit for given gain .

Q: How high must a receiving antenna be to receive a signal directly from an over-the horizon…

Q: Q6 Figure Q6 shows a closed loop control system of a servo motor. Assuming that the input…

A: The given figure of the closed-loop control system is shown below. We need to describe the…

Q: A strain gauge transducer is constructed in a Wheatstone bridge circuit configuration. In the null…

Q: 2. Find 1₁, 12 and 13. 1522 M 30V + 52 SI₁ W 12 30 W 12.2 13 دل 18 302 M 2012 2012

Q: ♫ Step +K- Gain 1 S Integrator Figure (4-3) 1 s+1 Transfer Fon Scope

Q: The Voltage across PS- and PS+ equals 17.0 volts. The T/C temperature = 103 degrees Fahrenheit.…

Q: What must be the value of E to ensure that the Current (I₁= 5mA) as shown. Calculate the power…

A: The given problem is from circuits. The detailed solution is given in the next step

Q: A 2-mH inductor is used in a fusion power experiment. If the current through the inductor is 5…

Q: 4) Determine the range of K for which a system with the following characteristics equation is…

Q: A 60 Hz sinusoidal voltage with an RMS value of 440 V is applied to a TRIAC voltage regulator. The…

A: it is asked to find the output DC voltage of given TRIAC voltage regulator

Q: Find the ratio V.(s)/V/(s) for the electrical network shown in below V(s) 1,(s) 1/s 1,(s) 1/s+1) in…

Q: A 480 V, 50 Hz, Y-connected, six-pole synchronous generator has the OCC shown in Figure below. This…

A: Since, the question posted by you has multiple sub-parts, we will solve the first three sub-parts…

Q: Using the superposition principle, find ix in the circuit given below, where R= 7 Q. Please report…

Q: ← OpAmp Linear Circuits Q.7 An op-amp has a slew rate of 10 V/μs. The largest since wave output…

Q: O

A: Given: the circuit in which the switch is closed for a long time (t<0); steady state condition L…

Q: Consider a system where the output y[n] is related to x[n] as follows: y[n] = c[n]x[n], where c[n] =…

Q: a) impulse current generator , generation of switching surges , generation of high frequency high…

A: We have tobriefly explain impulse current generator, generation of switching surges, generation of…

Q: An induction motor draws 45 kW at a 73% power factor from a lo AC line. a) What is the phase angle?…

A: Given data Active power, P=45 kW, Power factor, cosϕ=0.73 We need to determine phase angle, reactive…

Q: Q21. Consider a star-connected system with a reactance of 652 and resistance of 852 per phase is…

A: Given data: Resistance = 8 Ω Reactance= 6 Ω Supply voltage = 440 V

Q: The ac voltage gain magnitude can be calculated using Eq. (10.31): Re 2re providing an output ac…

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

Problem 09.037 - Admittance of a parallel combination of R, L and C
Determine the admittance Y for the circuit given in the figure. Take R = 40.
www
R
The admittance Yis
j8Q2
+ i
-j10 Q2
)) ms.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Two lossy capacitors with Equal capacitance values and power factors of 0.01 and 0.02 are in parallel, and the combination is supplied from a sinusoidal voltage source. The power factor of the combination is ?
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit