Prob 7. Steady - state creep data taken for stainless steel at a stress level of 70 MPa (10,000 psi) are given as follows: (8 marks) If it is known that the value of the stress exponent n for this alloy is 7.0, compute the steady - state creep rate at 1250 K and a stress level of 50 Mpa. é, (s-1) T (K) 1.0 X 10-5 2.5 X 10-3 977 1089

Prob 7. Steady - state creep data taken for stainless steel at a stress level of 70 MPa (10,000 psi) are given as follows: (8 marks) If it is known that the value of the stress exponent n for this alloy is 7.0, compute the steady - state creep rate at 1250 K and a stress level of 50 Mpa. é, (s-1) T (K) 1.0 X 10-5 2.5 X 10-3 977 1089

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steady-state creep rate data are given in the following table for a nickel alloy at 538 °C (811 K): o(MPa) 10-7 22.0 10 36.1 Compute the stress at which the steady-state creep is 104h' (also at 538 °C).
Steady-state creep data taken for an iron at a stress level of 140 MPa are given here: &, (h:¹) T(K) 6.4×104 1080 8.8 x 102 1180 If it is known that the value of the stress exponent n for this alloy is 8.5, compute the steady-state creep rate at 1290 K and a stress level of 82 MPa. i h1
The following creep data were taken on an aluminum alloy at 480 C (900 F) and a constant stress of 2.75 MPa (400 psi). Plot the data as strain versus time, a) then determine the steady-state or minimum creep rate. Note: The initial and instantaneous strain is not included. b) Identify at what time can a secondary creep region occur and at what time would it end to start the tertiary region in a creep curve: (see attachment).
O The following engineering stress-strain data were obtained for a 0.2% C plain-carbon steel. (i) Plot the engineering stress-strain curve. (ii) Determine the ultimate tensile strength of the alloy. (iii) Determine the percent elongation at fracture. Engineering Engineering Engineering Engineering Stress Strain Stress Strain (ksi) (in./in.) (ksi) (in./in.) 76 0.08 30 0.001 75 0.10 55 0.002 73 0.12 60 0.005 69 0.14 68 0.010 65 0.16 72 0.020 56 0.18 74 0.040 51 0.19 75 0.060 (Fracture)
An S-N plot from fatigue testing of a steel is provided below. Use the plot to determine the following values for this steel. 1. Fatigue limit: 2. Fatigue lifetime at a stress amplitude of: 415 MPa: 275 MPa: 3. Fatigue strength at: 5x104 cycles: 5x105 cycles 500 400 300 200 100 0 1.E+04 Stress Amplitude (MPa) 1.E+05 1.E+06 Cycles to Failure 1.E+07 1.E+08
X Incorrect. Steady-state creep rate data are given here for some alloy taken at 200°C (473 K): (h) a (MPa) 2.5x 10 2.3 x 102 71 If it is known that the activation energy for creep is 160000 /mol, compute the steady state creep rate at a temperature of 220°C (493 K) and a stress level of 48 MPa. the tolerance is +/-9% the tolerance is +/-9%
Sorry I forgot to add the table. I think the answers will change this time The following creep data were taken on an aluminum alloy at 480 C (900 F) and a constant stress of 2.75 MPa (400 psi). Plot the data as strain versus time, a) then determine the steady-state or minimum creep rate. Note: The initial and instantaneous strain is not included. b) Identify at what time can a secondary creep region occur and at what time would it end to start the tertiary region in a creep curve: (see attachment).
Case Study Calculate the Tensile Toughness Tensile toughness measures the total energy absorbed prior to fracture and is different from fracture toughness and impact toughness. Fracture toughness measures the resistance to fracture when a flaw (i.e. crack) is present in the material. Since it is nearly impossible and costly to manufacture materials with zero or near zero defects, fracture toughness is a major consideration for all structural materials. Impact toughness measures a materials ability to withstand an impact blow (i.e. high strain rates) and is particularly important in assessing the ductile-to-brittle transition behavior (more details later). Impact toughness is also commonly referred to as notch toughness. The tensile toughness can be estimated using the stress-strain curve by measuring the area under the curve (both the elastic and plastic regions). Tensile Toughness = f Stress, σ Ty- Ey Efracture ETS Ur Ey Efracture o de = U₁ + SETS o de + Sefracture o de Ey Ey o de =…
Steady-state creep data taken for an iron at a stress level of 136 MPa are given here: If it is known that the value of the stress exponent n for this alloy is 8.3, compute the steady-state creep rate at 1300 K and a stress level of 83 MPa. i Es (h-¹) T(K) 6.7 x 104 1100 8.5 x 10-2 1200 h-1
OWHATSAPP now Basel Wbdik tzbat kmnnn Practice Assignment 3- Chapter 6: Problem 1: . Consider a steel alloy having the stress-strain diagram shown in the figure below: 1. Determine the Young's modulus E, the ultimate tensile strength TS, the yield strength YS. 2. Estimate the ductility. 3. If the Poisson's ratio v= 0.35, calculate the shear modulus G. 400 T 100 400 300 200 200 100 100 0.004 0008 0.01 0.02 0.03 0.04 0.05 0.06 Strain Solution: Problem 2: The short cylindrical block of 2014-T6 aluminum, having an original diameter of 0.5 in. and a length of 1.5 in., is placed in the smooth jaws of a vise and squeezed until the axial load applied is 800 Ib. Given young's modulus 10.6x10 psi and ress (MPa)
Calculate the activation energy (in J/mol) for creep for an alloy having the steady state creep behavior shown in the figure. Use the data taken at stress level of 300MPA and temperature of 650C and 730C. Assume that the stress component n in independent of the temperature. 1000 800 600 650°C 400 730°C 200 815°C 100 925°C 80 60 40 20 10-6 10-5 104 10-3 10-2 10-1 10 102 103 Steady-state creep rate (h-) Stress (MPa)
/ steel has zero mean stree of 320 Mpa ,mean stress of 200 Mpa,tensile stress of 740 Mpa,yield stress of 1.5 tensile stress 1- Calculate the fatique limit by using the three equations of fatique behavior 2-sketch the fatique behaviour for eachs 3- which of the three eaquatons is more suitable for calculations fatique of glasses materials and why