Prepare the Bar bending schedule of a simply supported R.C.C. Lintels from the following specification: Size of lintel 300mm widex 200mm depth. Main bars in tension zone of Fe 250(grade I) 3 bars of 16mm dia., one bar is cranked through 45 degree at 170 mm from each end 2 No. anchor bars at top 8mm dia. Two legged stirrups@150mm c/c of 6mm dia. through out. Clear span of the lintel is 1150mm. Bearing on either side is 150mm

Prepare the Bar bending schedule of a simply supported R.C.C. Lintels from the following specification: Size of lintel 300mm widex 200mm depth. Main bars in tension zone of Fe 250(grade I) 3 bars of 16mm dia., one bar is cranked through 45 degree at 170 mm from each end 2 No. anchor bars at top 8mm dia. Two legged stirrups@150mm c/c of 6mm dia. through out. Clear span of the lintel is 1150mm. Bearing on either side is 150mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.2P

See similar textbooks

Similar questions

Question 1 Check that the medium-term load of 38 kN applied to the spaced column shown in below complies with the design requirements of BS 5268-2. The column consists of two 38 x 150 C22 timbers 76 mm apart. All joints are glued and intermediate packs are 250 mm long. suitable connection #### x ->89² 6:38. Y T -end blocking AP 100 intermediate blocking L₂ 1₁ x W L W EFH 400 m 38kN medium term load -ICHICHID -200 600 600 600 600 600 600 200 38kN medium term load
Prepare the Bar bending schedule of a simply supported R.C.C. Lintels from the following specification:Size of lintel 300mm wide x 200mm depth. Main bars in tension zone of Fe250(grade I) 3 bars of 16mm dia., one bar is cranked through 450 at 170 mm from each end2 No. anchor bars at top 8mm dia.Two legged stirrups@150mm c/c of 6mm dia. throughout.Clear span of the lintel is 1150mm.Bearing on either side is 150mm
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A channel shown is attached to a 12 mm gusset plate with 9-22 mm diameter A 325 bolts as shown. Use LRFD. Fnv = 300 MPa Fu = 400 MPa Fy = 248 MPa Ag = 3354 mm2 Question: Determine the capacity of the channel based on the bearing strength of the connection.
2 hEe c W@ B & - For the beam shown find the value of Force (F) Ib and maximum stress due to flexure ( oy ) psi if the shear force in bolts is 300Ib and the shear stress in beam 120psi. Spacing between bolts (S) =5in F T —————————————+% 4ft 8ft 1in 1in -~ - 10in 1n § 8in
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A tension connection consists of A36 steel double angles (two L4x4x1/4 shapes, or 2L4x4x1/4) fastened to a 4x10 No. 2 Red Oak member with a single row of four 0.875 inch A307 bolts. The connection is subjected to normal temperatures but wet in-service conditions. Assume the group action factor is C,=0.95 and the geometry factor is Ca=1. The controlling ASD load combination is D+ L where L is from occupancy. Elevation Cross Section L4x4x1/4 L4x4x1/4 Pa Р. 2L4x4x1/4 4х10 4x10 Plan L4x4x1/4 Pa/2 Pa 4x10 L4x4x1/4 Pa/2 • Determine the load, Pa, that the connection can support based on tension strength of the 4x10. Pa=. lb • Determine the load, Pa, that the connection can support based on gross tension yield of the double angles. The ASD design strength for gross tension yield is F,A,/1.67 where F=36 ksi, A,=1.93 in² for each L4x4x1/4. Pa=. lb
A double-channel shape, 2C8 x 18.75 is used as a tension member. The channels are bolted to a ¾-inch gusset plate with % - inch diameter bolts. The tension member is A572 grade 50 steel and the gusset plate is A36. If LRFD is used, how much factored tensile load can be applied? Consider all limit states. →2" popoy |-|-|-|-|-| n оо- 0 0 0 0 x + = ³/8" 288×18.15
The truss below is pin connected at A and E, and is acted on by the forces shown. E A D B Identify all of the ZERO-FORCE MEMBERS by checking the boxes below (if there are none, leave all boxes unchecked): BF AF BC BH CD EG -GH AB CH DG DH DE -FH
The details of an end bearing stiffener are shown in Figure . The stiffener plates are 9⁄16-inch thick, and the web is 3⁄16-inch thick. The stiffeners are clipped 1⁄2 inch to provide clearance for the flange-to-web welds. All steel is A572 Grade 50. a. Use LRFD and determine the maximum factored concentrated load that can be supported. b. Use ASD and determine the maximum service concentrated load that can be supported.
Q4) Determine the maximum service load than can be applied if the live load to DL ratio is 2. All structural steel is A36and the weld is a % inch fillet weld with E70 electrodes. Section is not double angle. Check if this weld size, length meets the code requirements? 2L5 x 3½ x %6 LLBB 5"
A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)