Pr A triangular gutter with a side slope at an angle of 60° has a depth of 300 mm. Find the velocity of water, if the slope of the gutter bed is 0.01? (c=50) C 250 m 30° 60° 1.36 m/s 2.36 m/s 0.136 m/s O

Pr A triangular gutter with a side slope at an angle of 60° has a depth of 300 mm. Find the velocity of water, if the slope of the gutter bed is 0.01? (c=50) C 250 m 30° 60° 1.36 m/s 2.36 m/s 0.136 m/s O

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.3P

See similar textbooks

Related questions

Q: F. A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels…

Q: in fig. FV=------ -? (gate width =8 ft) water weight density= 62.4 lb/ft3 Seawater Y=64 lb /ft³ 11ft…

Q: ice. h2 0.8 m and h3 - 2.4 m. Compute the settlement of the clay layer in millimeter caused by…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: Given data : a=7.5 m b=2.5 m w=27 KN/m P=44 KN MB=67 KN×m

Q: What conditions produced the best examples of overland flow? What factors may have contributed to…

A: Water that rushes across the land after rain, either before it joins a watercourse, after it leaves…

Q: Two channels sections the first is rectangular with water depth = 3 m and width=3. the second sec.…

Q: d) Determine the stress, strain and elongation/shortening of member AB (Assume Esteel = 200,000 MPa)

A: Lets the member is A992 steel So, fy = 345 N/mm2 E = 2 x 105 N/mm2

Q: estimate the volume of soil that fill the pot and the volume of material that was used to make the…

A: The values and diagram given in the question are as follows:

Q: Find The deflection at point, A totsN Find ACH₂eE₂ AFH EL 2m for the Frame 30 MN B sm EI shown below…

A: Horizontal and Vertical Deflection at A is zero as it hinges support. Here, the horizontal…

Q: d₂ B d₁ X1 A load P = 54 kN is applied at end C of the brass rods AB and BC. If E = 115 GPa,…

Q: A consolidated-undrained test on a normally consolidate clay yield the following results: Confining…

Q: tory system so that blood detours, through the vein, around an occluded coronary artery segment. Why…

A: Endoscopic vein harvesting is commonly used to extract the saphenous vein. A heart-lung machine is…

Q: fig. for FH, hcg= 11ft hcp. --? (The width =10 ft) Seawater y= 64 lb /ft³ A 6ft

Q: Calculate the void ratio of a soil sample having porosity of 0.32 and a moisture content of 25%.

A: given- porosity n=0.32moisture content w=25%=0.25

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to…

Q: It is proposed to design a ship. The proposed ship (prototype) is has a length of 150 m and wetted…

Q: P VIT A a WAC ļ↓↓ B a C WCD b D X

Q: Find The deflection at point, A totsN Find AcH₂OE, AFH C 1 for the Frame 30 MN shown below by unit…

A: Horizontal deflection and vertical deflection at A is zero due to hinge support.

Q: Support Reactions, Shear and Moment Equations. For the last segment use the FBD of the right…

Q: Two tanks are connected with the three pipes of length 2 m, 3 m, and 4 m and diameters 20 cm, 30…

A: Asked: To determine the equivalent diameter for the given pipes. Given: Pipe 1: Length (L1) = 2 m…

Q: Structural analysis 2 (1401303) HWs Question For structure below, complete the missing loading and…

A: solution 1. Fixed end moment -MFAB = + MFBA = wl8 = 36 × 88 = 36 KN-m-MFBC = + MFCB = wl212 = 6 ×…

Q: Geometry shapes or cross- section in an open channel are ectangular and trapezoidal only True O…

A: The statement is False

Q: , determine the magnitude F and direction 0 gnitude of 1400 lb.

Q: FH on the curved gate. Is S Water 4m -- -? If the gate width= 6 m F r=1my B 264600 NO 264600 lb O…

Q: Identify the different grades and different wood used in the Philippines,

A: Following are the main types of woods used in Philippines

Q: Q3 Block A movies on a roller along inclined surface and Connected to Block B by a link. Determine…

Q: 10 psig H to Free jet 1 in. dia. 3 ft 2 in. dia. *.?=In fig. V2 25.9 ft/s O 35.9 ft/s 15.9 ft/s

Q: نقطة واحدة In fig. if h1= 0.5 m, h2= 1.5 m and the fluid y2 S.G= 13.6, ylis water, what ?is the…

Q: 1. In each case, draw the shear and moment diagrams for the beam. 4 kN/m 4 kN/m --15m+ -3 m +1.5 m

A: Note: As per bartleby guidelines, if questions are not interlinked multipart type questions can be…

Q: Problem 1.2 Find the

A: solution of above problem is below:

Q: The figure shows a cutaway view of an assembly in which a solid bronze [G= 6,500 ksi] rod (1) is…

Q: The activities, duration, and cost under normal and accelerated crashed conditions for a network…

Q: 5. Find the total weight of a 10 ft³ tank of pressurized to 500 psia, the tank itself W

Q: Water In fig. if hp=2 m, find Ycp ?(a=45°) B FR Center of pressure a Centroid 7 Gate area = A y Уст…

A: To Determine Length Ycp given in the figure.

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: A moist soil sample having a volume of 1.58 m³ has a total mass of 2,323 kg. Specific gravity of…

Q: 13. Determine the safe concentrated load that the 175 mm x 375 mm simple beam could carry over a…

Q: What is maximum capacity of measure should be used in determining the density of the concrete if the…

A: B) 14 Liters

Q: 3. The steel crane rails of MRT are laid with their adjacent ends 3.2mm apart when the temperature…

Q: Determine the moments at all supports. 2 KN 2 kN 4 kN/m 6 kN/m 2 m 4 m 4 m 3 m 1 m/ R₁ R₂ R3 V4…

Q: PROBLEM 2: Draw the shear and bending moment diagrams for the beam shown. a. Determine the maximum…

Q: In figure, Hf in pipe 1 = Hf in pipe 2 =Hf in pipe 3 Pipe 1 Pipe 2 B Pipe3 True O False O

Q: Interconnection of sewer service pipe into a sewer main is made by punching the sewer main a hole to…

A: answer:- On the top of sewer main Explanation :- Interconnection of sewer service pipe into a…

Q: indicate the final answer in 3 decimal places.

Q: F. A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels…

Q: The calculations in differential leveling works are limited only to determining the heights of the…

A: Given data in question Differential levelling work To find out Statement above is True or False.

Q: The depth of water below the spillway and after hydraulic jump are 1 m and 6 m respectively. The…

A: given- depth of water below spillway y1=1 mdepth of water after hydraulic jump y2=6 m

Q: indicate the final answer in 3 decimal places.

A: To Determine The consolidated undrained friction angle (Φ)

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: L = 9m

Q: IN fig. for FH, hcg= 11ft hcp. -? (The width =10 ft) Seawater y=64 lb /ft³ 6ft B 6.375 ft, 6 ft 8…

A: Answer We need to calculate the centroid of submerged quarter circle(hcg) and Centre of pressure…

Question

Pr
A triangular gutter with a side
slope at an angle of 60° has a
depth of 300 mm. Find the
velocity of water, if the slope of
the gutter bed is 0.01? (c=50)
C
250 m
30°
60°
1.36 m/s
2.36 m/s
0.136 m/s O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

See figure below Surt Pol Level rectangular channel with d1 = 5 ft d2 15 ft Q/B= 37 8 cfs/ft bed slope 0.0015 Calculate AE-1 distance between 1 and 2 2
Two leveling rods placed at a distance of 50m. and 100m. respectively from the instrument gives an intercept of 0.488 m. and 0.980 m. Determine the stadia interval factor. P.S COMPLETE SOLUTION/ STEP BY STEP SOLUTION. THANK YOU
From the given profile leveling notes. a) What is the difference in elevation between station 5 and 3. b) Compute the elevation of TP2. c) Compute the elevation of BM2. STA BS FS IFS ELEV BM1 | 0.95 225.50 1 3 2.3 ТР1 3.13 0.64 2.7 4 2.8 3.1 0.5 7 0.8 TP2 2.16 | 1.28 8 0.9 9. 1.2 10 1.7 11 2.8 ТРЗ 0.82 | 2.37 ТР4 1.35 3.50 12 3.0 BM2 1.24 3. 5.
It is desired to transport 20 cfs of water through a rectangular finishedconcrete (n = 0.012) canal that can be at most 5 ft wide. The slope of theland through which it passes is 0.0004. The depth of water, in ft, thatshould be expected is nearest: A. 1.83B. 1.28 (Incorrect Answer)C. 1.63 D. 1.01
A rectangular channel has a width of 3.6m with a roughness coefficient of 0.013 Compute the critical slope Choices: 0.83 0.083 0.00308 0.38 NOTE: In the given question that is all that is given there is no discharge given please help this is the only information that is given i this question
Determine the T3, If y=18m. * 10 m 60 KN 40 KN 80 KN 30 m 50m 50m -30m O 158.678 KN O 179.013 KN O 164.746 KN O None of the above O 181.707 KN
12 water flows fromastovage reservoirinta Channel which is (20 ft) wide, the channel rectangular Section and (4ft) below the surface of storage. Calculate the maximum discharge and minimum slope required ( Assume smooth Cement lining of = 0,01 and neglect entrance (asses)?
The following data were taken along a center line of a dam AB. The staff had been held in the 1st case at a starting point (A) and then at 20m intervals. The staff readings were: 0.765 / 1.064/ [0.616] / 1.835 / 1.524. The level was then moved forward to another position and further readings were taken as follows: 2.356 / 1.378 / [2.063] / 0.677/ 2.027. The last reading was at point (B). The R.L of (A) is 41.819m. 1- Enter the above data in a level book form. 2- Find the reduced level of points using height of collimation method. 3- Check the results. 4- Calculate the gradient from A to B. Note: readings in brackets are inverted staff readings.
Complete the Differential Leveling Notes by providing data to the unknown quantities. Please show complete solution.
Q1). Calculate the volume of cut and fill from followings: bo = 6m, s = 10, n = 1 in cut, n = 2 in fill, assume left side higher than right side, the stations and elevations are taken along centerline." St. N.G. Elev. 87 88 1972 12+60 12+80 Design Elev. 82 94
Hi! Help me with this please. Thank you so much! A dumpy level is set up at one end of a line 160m. long for the purpose of determining the instrument stadia interval factor. The line is marked by hubs at every 40 m. and a stadia rod is held at each hub. The stadia intercept at each location of the rod were observed as follows: 0.402, 0.813, 1.231, 1.602 respectively. Compute the average value of the stadia interval factor. Height of instrument is 1.5m.
B 15 kN 20 kN 3. E D 3 m 3 m