Poles 4500 g

Q: Consider an ideal air-standard diesel cycle in which the state before the compression process is 95…

A: Given data Conditions before compression:P1 = 95 kPaT1 = 290 KCompression ratio = CR = 20We have to…

Q: Two mercury barometers are placed at the basement and rooftop of a building. Measurements are taken…

A: Reading at the basement, hbasement= 654 mm= 0.654 m Reading at the rooftop, hrooftop= 480 mm= 0.480…

Q: 3. The motion of the particle along a straight line is governed by the relation a = t³ – 2t² + 7…

A:

Q: What size of hole must be drilled in an M 42 bolt to make the bolt of uniform strength

A:

Q: 3 For each case from the truss structures shown identify the ZERO FORCE МОМЕВER CASE 1 CASE 2

A: identify the zero force members.

Q: H.W. 1: For the area shown below, determine the location of centroid. 0.25 cm 1 cm Hole (r= 0.5 cm)…

A: find the coordinates of centroid of the shaded area.

Q: Engine pressure ratio in a turbojet engine is the ratio between the fan and turbine outlet…

A:

Q: Use SMART problem-solving methodology and find the sum of the three harmonic motions x;(t) =…

A: Write the all three expressions of harmonic motion. x1t=10cosωt+2x2t=15sinωt+2x3t=15cosωt

Q: 2. The following data were obtained in a study of the relationship between the weight and chest size…

A:

Q: 1. Calculate the power required at the pump shaft given that the wate density and flow rate are…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: One of the smooth vertical walls supporting end B of the 145-kg uniform shaft is turned through a…

A:

Q: Express in polar ej14 + 943 - (8-j6) /j- answer must be in polar form (i.e. 20.02angle180:…

A:

Q: The torquemeter system may be ysed also for automatic propellre feathering propeller pitch…

A: The torquemeter system may be used also for automatic propeller feathering.

Q: Q1 For a certain incompresible flow field, it is suggested that the velocity components are given by…

A:

Q: In a counter-current-flow tubular heat exchanger, a liquid food (milk), flowing in the inner pipe,…

A:

Q: A vapor-compression refrigeration system using ammonia as refrigerant is to be used to cool 45,000kg…

A:

Q: 1. Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine…

A:

Q: One of the smooth vertical walls supporting end B of the 145-kg uniform shaft is turned through a…

A: The moment of a force is a measurement of the force's turning impact on the body on which it is…

Q: Energy transferred as heat occurs between two bodies in thermal contact when they differ in which of…

A: We know that, heat is just a form of energy which is always in transit. It gets transferred from…

Q: answer the question below. Robotic arms can have different end effectors. An end effector is the…

A: Solution is attached below;

Q: Calculate the heat transfer rate when a steel pipe conveying steam is insulated. The pipe has an…

A: GIVEN DATA- The pipe has an inside diameter of 20 cm, and an outside diameter of 30 cm insulation…

Q: A square plate of 0.255 kg mass and 0.5 m side slides down a plane, inclined at an angle of 30° to…

A: Mass of the square plate, m= 0.255 kg Side length of the square plate, b= 0.5 m Angle, θ= 30∘…

Q: kindly help me with this one. Write your answer with four decimal places and enclose them in a box.…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Determine the force on members AD, AC, AB,DB A 900 N 225m 900 N 225m

A:

Q: 6- A liquid has a specific weight of 59 lb/ft and a dynamic viscosity of 2.75 lb . s/ft?. Determine…

A:

Q: oI water from a fixed nozzle has a diameter d of 30 mm and strikes a flat plate at angle u of 30° to…

A:

Q: The armature of a variable-speed electric motor, of mass 200 kg, has an unbalance due to…

A: first we calculate the natural frequency  then evaluate the transmission ratio

Q: 2. Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine…

A:

Q: Question 2 A refrigeration cycle operates with R-134a. State 1 State 2 Saturated 15 psia 180 psia…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: The 300-N block is at rest on the horizontal plane before the force P is applied at t=0. Find the…

A: Weight of the block, W= 300 N P= 80t μs = 0.4 μk = 0.2 The 300-N block is at rest on the horizontal…

Q: A shaft is loaded with a centre load of 7000 N between two bearings and an overhanging load of 4000N…

A:

Q: The coil has a mass of 90 kg and a rotating radius of 0.3 m. If the static and kinetic friction…

A:

Q: he ends A and D of the two solid shafts AB and CD are fixed, while the ends B and C are connected to…

A: Given:dAB=60 mmrB=100 mmrc=40 mmdCD=45 mmζallow=50 MPa

Q: 3- The plane in the space is determined by three points that are not on straightening one O right…

A: Explanation: 3) A plane in space is determined by three points that are not in straight line.  For…

Q: A proper free-body diagram for a fixed support in two-dimensional analysis has: O A force in the x…

A: identify the reaction at fixed support in 2 - D.

Q: 5. One Kmol of CSH18 is burned with 100% air containing 25 Kmol of O2. Determine the air- fuel ratio…

A:

Q: Two solid steel shafts, each 30 mm in diameter, are connected by the gears shown in the figure.…

A:

Q: The torquemeter in a turbopropeller engine measures the torque transmited trough the compressor…

A: Torquemeter is an equipment which measures torque.

Q: One kg of steam at 255.55 °C and with an enthalpy of 1873 kJ/kg is confined in a rigid container.…

A:

Q: 303. Á steel shaft with a constant diameter of 50 mm is loaded as shown in Fig. 3-5 by torques…

A: Given                 Diameter, d = 50 mm                                    = 0.05 m Modulus of…

Q: Choose the correct answer Mcq: the main type of stress in gear tooth is ? A-shear stress B-tensile…

A: what are the main stresses in the gear tooth.

Q: A square tube is welded on one side and will be filled with liquid of a relative density c 1.15. An…

A: Given Relative density of the fluid inside the tube s1=1.15Relative density of the fluid in the…

Q: A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston- cylinder device…

A: Given that, Mass of vapor, m=5 kg,Initial pressure of cylinder, P1=100 kPa,Mass of liquid, mf=2…

Q: 1. The light bar is used to support the m kg block in its vertical guides. If the coefficient of…

A: fig:FBD of block ∑Fv=0Fy=W=218*9.81=2138.6 N

Q: 19.12 A certoain double-pane window consists of two glass sheets, each 80 cm x 80 cm x 0.30 cm,…

A:

Q: Q3: Air in an ideal Diesel cycle is compressed from 3 L to 0.15 L, and then it expands during the…

A:

Q: When a horizontal roll vortex is pushed vertical, what is created?

A: The wind shear causes the air to have a horizontal rotation. The strong updrafts from the rising…

Q: A Carnot engine requires 40KW from the hot source. The engine produces 20kw of power and the…

A:

Q: The maximum temperature that can be reached in a dual-combustion cycle is 2000°C, and the pressure…

A:

Q: rod is 0.5 m long and 5 mm diameter. It is stretched 0.06 mm by force of 3 kN. Calculate stress and…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.