piece made of pure aluminum has a diameter D = a.x ^ 1/2 and a = 0.5m ^ 1/2. The left edge surface of the part is at x1 = 25 mm, and the right edge surface is x2 = 125 mm. Edge temperatures are T1 = 600K and T2 = 400K and the side surface is completely insulated. a) Assuming that the heat conduction is one dimensional, write a relation for the temperature distribution T (x). b) Calculate the heat transfer.

piece made of pure aluminum has a diameter D = a.x ^ 1/2 and a = 0.5m ^ 1/2. The left edge surface of the part is at x1 = 25 mm, and the right edge surface is x2 = 125 mm. Edge temperatures are T1 = 600K and T2 = 400K and the side surface is completely insulated. a) Assuming that the heat conduction is one dimensional, write a relation for the temperature distribution T (x). b) Calculate the heat transfer.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.3P: 1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of...

See similar textbooks

Similar questions

The heat conducts through the shape below. The temperature of the right face is 93 °C, while the left face is at 23 °C. If the top and bottom faces are completely insulated, and the thermal conductivity of the material decreases with decreasing temperature. * Assume that the thermal conductivity is 100 at 23, decreased to 10 at 93. A) Sketch the temperature profile inside the plate. B) If both sides of the plate in the above problem is exposed to air: Left side (h = 20 W/m2K, TL = 20 °C) and right side (h = 90 W/m2K). Calculate the temperature of the air on the right side.
A boiler furnace wall must have a heat loss no greater than 700 Btu/hr~ft2 and is madeof a material with a thermal conductivity of 0.60 Btu/hr~ft~F. The inner wall surfacetemperature is '2000°F, and the outer surface temperature is 800°F. What wall thick~ness is required?
A metal rod 1 sq. in. in cross section and 6 in. long is heated at one end and cooled at the other. If the rate of heat input is 3 BTu/hr and the difference in temperature of the two ends is 2 deg. F, what is the coefficient of thermal conductivity in BTU/(hr)(ft²)(⁰F/ft)?
A solid body of length L with a rectangle cross section has a temperature distribution equals to : T = (- C/k)*e^(-x)+Cx+D. K is the conductivity and it is equal to 1 W/m.k. At x= 0 the temperature is equal to 373 K. At x= L the body is well insulated. What should be the value of heat generation so that the body is in steady state: O a. B+e^(-x) O b. B*e^(x) C*e^(-x)
A wall consists of a layer of wood and a layer of cork insulation of the same thickness. The temperature inside is 34.0°C, and the temperature outside is 0.0°C. The thermal conductivity of wood is 0.130 W/(m·K) and the thermal conductivity of cork is 0.0460 W/(m·K). A) What is the temperature at the interface between the wood and the cork if the cork is on the inside and the wood on the outside? in C B) What is the temperature at the interface if the wood is on the inside and the cork is on the outside? in C C) It doesn’t matter whether the cork is placed on the inside or the outside of the wooden wall because the temperature at the interface differs for the two cases.the temperature at the interface differs for the two cases. the temperature at the interface is the same for the two cases.the temperature at the interface is the same for the two cases. the total thermal resistance is the same for the two cases.the total thermal resistance is the same for the two cases.…
2. One end of a 40 cm metal rod 2.0 cm2 in cross section is in a steam bath while the other end is embedded in ice. It is observed that 13.3 grams of ice melted in 15 minutes from the heat conducted by the rod. What is the thermal conductivity of the rod.
4. A spherical steel reaction vessel has an outer radius of 2.0 m and is covered in lagging 250mm thick. The thermal conductivity of the lagging is 0.4 W/m K. The temperature at the surface of the steel is 340⸰C and the surface temperature of the lagging is 45 ⸰ Calculate the heat loss.Thermal Conductivity;k=385 W/mK
A mechanic needs to remove a tight fitting pin of material A from a hole in a block made of material B. The machinist heats both the pin and the block to the same high temperature and removes the pin easily. What statement relates the coefficient of thermal expansion of material A to that of material B?
Please provide accurate answer with proper steps The wall of the furnace is 30.48 mm thick and is insulated from outside. Thermal conductivity of the wall material is 0.1 W/m K and the insulation material is 0.01 W/m K. The furnace operates at 650 0C and the ambient temperature is 30 0 Allowable temperature on the outer side of the insulation is 1000C. Determine the overall heat transfer by conduction per unit area occurring across a furnace wall made from clay. If the air side heat transfer coefficient is 0.4 W/m2 K, calculate the minimum insulation thickness requirement.
A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the other end is at x = 3. The thermal diffusivity of the bar is k = 0.4. The bar's initial temperature f(x) = 50 degrees Celsius. The ends of the bar (x = 0 and x = 3) are then put in an icy bath and kept at a constant 0 degrees C. Let u(x, t) be the temperature in the bar at x at time t, with t measured in seconds. Find u(x, t) and then u4 (2, 0.1). Put u4(2, 0.1) calculated accurately to the nearest thousandth (3 decimal places) in the answer box.
Q1. Consider the composite materials shown in figure. 1. Sketch the equivalent thermal resistance. 2. Calculate the heat transfer per unit area of the wall. 3. Determine the temperatures at interface between the layers. Material A k (W/m K) 2.1 B 6.7 C 3.5 T-15 °C C B C 195 1/4 14h-10 W/m² K -T=50 °C HATH 320.0020 30 mm -
A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the other end is at x = 3. The thermal diffusivity of the bar is k = 0.4. The bar's initial temperature f(x) = 300 degrees Celsius. The ends of the bar (x = 0 and x = 3) are then put in an icy bath and kept at a constant O degrees C. Let u(x, t) be the temperature in the bar at x at timet, with t measured in seconds. Find u(x, t) and then u7 (2, 0.1). Put uz (2, 0.1) calculated accurately to the nearest thousandth (3 decimal places) in the answer box.