Part 1: Modeling Passive Transport Explain why the resistance of the current path through the extracellular fluid is much smaller than the resistance of the current path through the axoplasm. Extracellular fluid membrane axoplan membrane Extracellular fluid (Fig 3) Axon: Simple cylinder model A long axon can be modeled as a chain of many short segments like the segment described above. The dashed lines in Figure 4 below visually divide the axon into five such segments. Sketch the path of current flow onto the diagram and then design a circuit model for it. Check your model with your instructor. (Fig 4) Axon: chain of many segments Use the relationship between resistance, resistivity, length, and cross-sectional area to estimate values for the resistances of a membrane segment Reem and an axoplasm segment Reson.

Part 1: Modeling Passive Transport Explain why the resistance of the current path through the extracellular fluid is much smaller than the resistance of the current path through the axoplasm. Extracellular fluid membrane axoplan membrane Extracellular fluid (Fig 3) Axon: Simple cylinder model A long axon can be modeled as a chain of many short segments like the segment described above. The dashed lines in Figure 4 below visually divide the axon into five such segments. Sketch the path of current flow onto the diagram and then design a circuit model for it. Check your model with your instructor. (Fig 4) Axon: chain of many segments Use the relationship between resistance, resistivity, length, and cross-sectional area to estimate values for the resistances of a membrane segment Reem and an axoplasm segment Reson.

Stars and Galaxies (MindTap Course List)

10th Edition

ISBN:9781337399944

Author:Michael A. Seeds

Publisher:Michael A. Seeds

Chapter19: Astrobiology: Life On Other Worlds

Section: Chapter Questions

Problem 1SP

See similar textbooks

Similar questions

Analyze the two pictures below. Boy and Ben are brothers. Boy is a smart and responsible boy. He spent his time reading and answering his modules in school. While Ben is lazy and consumes most of his time playing online games on his cellphone. Now, write a 4-paragraph composition that shows comparison and contrast between the two pictures.
1. SHOW ALL YOUR CALCULATIONS ON AN ATTACHED SHEET FOR CREDIT! Use mesh analysis to complete the following table: Variable Calculated Value Variable Calculated Value LA IB I2 Ic I3 I4 Is 2. Simulate the circuit in Multisim. Place probes or meters for each quantity in the table and verify your computations. A printout of your simulation should accompany your pre-lab.
Simply the circuit to get the equivalent circuit. Show all circuits step by step. R1= 8 ohms, R2= 30 ohms, R3= 6 ohms, R4= 9 ohms, V= 54V A. What is the equivalent resistance?B. What is the current in R2?C. What is the potential difference across R3?D. What is the power dissipated in R4?
Hi, I need help solving this question using the diagram below, I got positive values for I1, I2, and I3, but my friends say she got I1 and I2 as negative values and then I3 as positive. R1= 220 ohms, R2 = 330 ohms, R3 = 390 ohms. then v1 is 12 volts.
Describe the relationship between voltage, current, and resistance. Provide graphs as needed for further explanation. Limit your answer to at most ten sentences.
Learning Goal: To analyze op-amp circuits that invert the voltage applied to the negative op-amp terminal. Before proceeding, review inverting op-amp circuits and the ideal op-amp assumptions. For the circuit shown (Elgure 1). determine Va when R = 6.0 k2. Ry - 7.8 k2. V, - 520 aV, and V= 15 V Express your answer to three significant figures with appropriate units. Vo = Value Units Figure m x V. Assume that m = 79, R, = 8.0 k2, V = 15 V and that the op-amp For the circuit shown (Eigure 1). determine Ry such that Vo is in its linear region of operation. Exnracs vour answer in kiloohms to four significant figures. R3 =
schematic diagrams simplify your representation of a circuit. it provides an easier way of representing simple and even complicated circuits. similarly, how do you work on a big and complicated project or problem? do you come up with a plan first? explain
Part A During an action potential, Na+ jons move into the cell at a rate of about 3 x 10-7mol/m2 - s. How much power must be produced by the "active Na+ pumping" system to produce this flow against a +30-mV potential difference? Assume that the axon is 90 cm long and 30 um in diameter. Express your answer using two significant figures. P = W Submit Request Answer
Problem solving. Show your solutions every question. 1. A battery is connected across a light bulb with an internal resistance of 80 ohms. Using an ammeter, the current flowing in the circuit was measured to be 150 mA. What is the voltage of the battery? 2. A hair dryer pulls a current of 8000 mA from a 120 V power source. What is the internal resistance of the hair dryer? 3. What is the value of voltage in the picture?
Directions: Write the letter of your answer on a separate sheet of paper.1. With 21 V applied, if R1 = 5 ohms, R2 = 35 ohms, and R3 = 14 ohms, whatis the current in R2 if R1 is connected in series with the parallel circuit R2and R3?A. 200 mA B. 400 mA C.600 mA D.800 mA 2. What is the total resistance of a circuit when R1 (7 kΩ) is in series with aparallel combination of R2 (20 kΩ), R3 (36 kΩ), and R4 (45 kΩ)?A.4 kΩ B.17 kΩ C. 41 kΩ D. 108 kΩ
Physics Hand writing please. Explain how to find an internal resistance of a battery given two resistors, batteries, and a multimeter(s). Draw-up procedure on how to perform this experiment. Include a circuit(s) diagram to illustrate your procedure.
ing Forward If three resistors connected in series to a battery. Suppose R, carries a current of 16A, R2 has a resistance of 50, and R3 dissipates 70W of power. What is the voltage across R3 and Resistance of R3 ? 1. Voltage (in V) across R3 %3D and 2. Resistance (in 2) of R3 = Next nage to search