P7.2 Consider the loop transfer function of a phase-lockloop systemL(s)G(s)G(s)Ge(s)G(s) = KK-10(s+10)s(s + 1)(s+100)Sketch the root locus as a function of the gainK,K,K. Determine the value of K, attained if thecomplex roots have a damping ratio equal to 0.60 [13].

Let's proceed to sketch the root locus.To sketch the root locus, we start by marking the poles and…

Answered: P7.2 Consider the loop transfer…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch the root locus of the system whose open loop transfer function is G(s)=k/s(s+4)(s+6). Find the value of k so that damping ratio of closed loop system is 0.6.
From a compliance transfer function of a spring-mass–damper system, the stiffness is determined to have a value of 0.6 N/m, a natural frequency of 0.50 rad/s, and a damping coefficient of 0.089 kg/s.1. Neatly derive the expressions of the magnitude and phase of the mobility transfer function
Measurements conducted on a servomechanism show the system response to be: C (t) = 0.3 e 60t + 1.5 e 10t, when subjected to a unit step input. [1].Obtain the expression for the closed-loop transfer function. [2].Determine the undamped natural frequency and damping ratio of the system.
1)The circuit shown below is initially, for t < 0, with capacitor C connected to a battery (Vbat = 12 V). The key is switched at t = 0, disconnecting the battery and turning on the capacitor to the rest of the circuit.a) Determine the energy stored in the circuit at t = 0 . b) Draw an equivalent circuit for the frequency domain, valid for t ≥ 0. Indicate the values of all components of the equivalent circuit.c) Determine the expression for the loop current in the frequency domain, I(s), expanded into partial fractions.
Circuit analysis 2 In the circuit shown below, ic (t) value for t <0 is equal to which of the following?
A hard disk drive (HDD) is an electro-mechanical data storage device that stores and retrieves digital data using magnetic storage and one or more rigid rapidly rotating platters coated with magnetic material. Figure 1 shows a simplified block diagram of a HDD. For analysis purposes, given gain K=30 and G(s)=1 / s(s+4) determine the open-loop and closed loop poles of the HDD and plot these separately in the S-Plane. Also discuss the stability using two different approaches.
Solution please. Should correct Consider a first order system with a transfer function of G(s) = K / (s + a), where K = 5 and a = 10. If the system is subjected to a ramp input of 2t, what is the steady-state error of the system? Show your calculations and assumptions.
A system has a damping ratio of 0.5, a natural frequency of 100 radians per second, and a dc gain of 1. Do the following: a)find the transfer function that describes the system. b) identify the type of response, giving details on why you came up with such identification. c) compute for the exact expression of its step response.
The transfer function of a continuous causal LTI system is given below. is undecided. ?(s) =1/s-3 To stabilize the system, a backstop with a constant K coefficient is required as shown in the figure below. It is desired to make the HSÇ stable by pulling the unstable pole to the stable region with the feeding. a K Calculate whether there is a feedback coefficient and, if so, the range of values.
For the following circuit, find the transfer function H(s)=I(s)/Vin(s) , at responses i(t) to zero input and zero state, the total response i(t), responses to transient and steady state and natural frequencies. Rate it also the circuit regarding the type of damping (overdamped, underdamped, critically damped). Consider vin = 100 u(t) V and that in t = 0 the capacitor voltage is 16 V and the inductor current is 0 A. Use only the resolution via Laplace transform. Any other methods used will not be considered.
Problem 1: Find the transfer function, using the standard formula for a second order system. for a second order system. Establish the relative damping factor and the natural frequency. Tell whether according to the value ? the system is suitable.
Determine the pole-zero plot of the impulse response of a single pole causal LTI system given in the picture

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

P7.2 Consider the loop transfer function of a phase-lock loop system L(s)G(s)G(s) Ge(s)G(s) = KK- 10(s+10) s(s + 1)(s+100) Sketch the root locus as a function of the gain K,K,K. Determine the value of K, attained if the complex roots have a damping ratio equal to 0.60 [13].