P.3.3 Oil of sp.gr. = 0.9 flows through a vertical pipe (upwards). Two points A and B one above the other 40 cm apart in a pipe are connected by a U-tube carrying mercury. If the difference of pressure between A and B is 0.2 kg/cm, 1- Find the reading of the manometer. 2- If the oil flows through a horizontal pipe, find the reading in manometer for the same difference in pressure between A and B. Ans, 1- R= 0.12913 m. 2- R= 0.1575 m.

P.3.3 Oil of sp.gr. = 0.9 flows through a vertical pipe (upwards). Two points A and B one above the other 40 cm apart in a pipe are connected by a U-tube carrying mercury. If the difference of pressure between A and B is 0.2 kg/cm, 1- Find the reading of the manometer. 2- If the oil flows through a horizontal pipe, find the reading in manometer for the same difference in pressure between A and B. Ans, 1- R= 0.12913 m. 2- R= 0.1575 m.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A bicycle wheel has a diameter of 64.6 cm and a mass of 1.87 kg. Assume that the wheel is a hoop with all of the mass concentrated on the outside radius. The bicycle is placed on a stationary stand and a resistive force of 125 N is applied tangent to the rim of the tire. (a) What force must be applied by a chain passing over a 8.96 cm diameter sprocket if the wheel is to attain an acceleration of 4.49 rad/s22? (b) What force is required if the chain shifts to a 5.57 cm diameter sprocket?
Mechanics Arz Yahya, PH.D. Example 2: The 30-kg pipe is supported at A by a system of five cords. Determine the force in each cord for equilibrium.
An aluminum wire having a cross-sectional area equal to 4.60 x 10-6 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s
SITUATION 1 (Fluid Flow in a Closed Conduit) Consider a fluid, with density (p) of 998.21 kg/m³ and dynamic viscosity (u) of 1.002 x 103 N-s/m², flowing in a 2000-meter long, 50-mm diameter smooth round pipe with velocity of 2.5 m/s. The energy loss on the pipe flow (he) due to friction between the pipe and the fluid is determined using Darcy-Weisbach equation, given as h₁ = f (²) (1/1) where f is the friction factor, L is the length of the pipe, D is the diameter of the pipe, V is the velocity of the flow, and g is the gravitational acceleration. The friction factor may be determined using an empirical equation developed by Nikuradse for flow in smooth pipes, given as 1 =0.869 In (Re√7)-0.8 where Re is the Reynolds number of the flow, determined as VDp R₂ = μl The friction factor equation given is only valid for flows with Reynolds number higher than 4000 (turbulent flow). Guide Questions: Determine the Reynolds number of the flow. Is the Nikuradse equation for friction factor…
The circular rod shown is made of the steel alloy AISI 4140 OQT 900. It has a diameter of 1.00 in and an initial length of 48 in. An axial tensile load of 15 000 lb. is applied during a certain operation. Compute: 1. the equivalent spring constant K, 2. the deformation X of the rod. The Young's modulus of the steel is known to be 30,000,000 psi. F=15 000 lb L= 48 in F=15 000 lb
1. Determine the equation of the line through the given point (a) parallel and (b) perpendicular to the given line Given: Point: ( -1,-4) Line: 4x-2y=3
Air at 30 oC flowing over a flat plate 10 points 0.5 m long and 0.6 m wide, is to be maintained at 70 oC . Determine the velocity of air which must flow over a side of 0.5m. The rate of energy dissipation from the plate is 3 KW.
Q.4 In an experimental setup, mineral oil is filled in between the narrow gap of two horizontal smooth plates. The setup has arrangements to maintain the plates at desired uniform temperatures. At these temperatures, ONLY the radiative heat flux is negligible. The thermal conductivity of the oil does not vary perceptibly in this temperature range. Consider four experiments at steady state under different experimental conditions, as shown in the figure Q1. The figure shows plate temperatures and the heat fluxes in the vertical direction. What is the steady state heat flux (in W m) with the top plate at 90°C and the bottom plate at 45°C? [4] 30°C 70°C 40°C 90°C flux = 39 Wm-2 flux =30 Wm2 flux = 52 Wm 2 flux ? Wm-2 60°C 35°C 80°C 45°C Experiment 1 Experiment 2 Experiment 3 Experiment 4
2. Heat conduction in a square plate Three sides of a rectangular plate (@ = 5 m, b = 4 m) are kept at a temperature of 0 C and one side is kept at a temperature C, as shown in the figure. Determine and plot the ; temperature distribution T(x, y) in the plate. The temperature distribution, T(x, y) in the plate can be determined by solving the two-dimensional heat equation. For the given boundary conditions T(x, y) can be expressed analytically by a Fourier series (Erwin Kreyszig, Advanced Engineering Mathematics, John Wiley and Sons, 1993):
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques as shown in Fig. 3. A 44-mm-diameter hole has been drilled into portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 77 GPa, determine the total angle of twist at end A. D 0.6m 60 mm 2000-m 1.2.m 250 №-m 30 mm 04m
For an object of mass m=3 kg to slide without friction up the rise of height h=1 m shown, it must have a minimum initial kinetic energy (in J) of: h O a. 40 O b. 20 O c. 30 O d. 10
4. The outer facing of a room is constructed from 0.75 m thick brick, 25 cm of mortar, 12 cm of limestone (k=0.186 W/mK) and 0.5 m of plaster (0.096 W/mK). Thermal conductivities of mortar and brick are both 0.52 W/mK. Assume that the heat transfer coefficients on the inside (plaster side) and outside (brick side) surfaces of the wall to be 8 and 24 W/(m^2 K), respectively. Calculate the overall coefficient of heat transfer (W/(m^2 K). Show your solution