nded from a rope is pulled aside with a below Calculate: -

Q: METHOD OF FRAMES

A:

Q: calculate : Output - 200 lakhs energy input - 7% of output material input - 250% of energy input…

A: Calculated partial productivity .

Q: where do v sub 1 came from? which is 0.95m/s

A:

Q: Q3/ the observed time for an operation of packaging a machine tool is 2 min. for the rating 140 %…

A:

Q: A steel shaft transmits 50 Bhp at 1400 rpm. Find the torque in in-lb.

A: Given data: PB=50 hpN=1400 rpm Need to determine the torque in in.lb.

Q: (a) A body of weight 55 N is placed on a rough horizontal plane. To just move the body on the…

A:

Q: ed with a horizontal 100 N force, At which

A: given:horizontal load P=100N

Q: . What is the angle 0 for this condition?

A: first of all find general expression of R in terms of theta, with the help of equation of motion.…

Q: Find the load lifted in N by t

A: GIVEN- Dsmall = 4cm Dlarge= 20cm Force = 120N To find- Load lifted by large piston

Q: A hydraulic jack receives a force of 100N and produces a force of 1kN to lift a certain load. Find…

A:

Q: Qu write Bernoullis Equation for given tigure 2

A: Energy at any two point in moving fluid is same .  Energy 1= Energy 2…

Q: dimension L4 in mm for assembly condition would be:

A: For the given assembly: L1=22.0±0.01 mm L2=10.0±0.005 mm L3=10.0±0.005 mm It is required to…

Q: Find the V-X and M-X diagrams. For the value of P use 182 kips. show all steps

A: Draw the free-body diagram of section DC. Apply moment equilibrium about point D.…

Q: and the

A:

Q: E, calculate the internal pressure

A:

Q: ADISIDO diameter is 10 times the tube thickness, find the thickness (mm) of the tube.

A: Given   Load, P = 500 kN     Stress = 140 MPa Find   Thickness, t

Q: a circular copper rod is 20.02 mm in diamter and has to be insterted into a square hole that is 20.0…

A: Given, Origianl diameter = D0 = 20.02 mm Final diameter = D = 20 mm   For pure copper, coefficient…

Q: (a) Find the curl of the centrifugal force. Comment on your result.

A: 3 (a) Centrifugal force is directed radially outward from that aixs F→=mω2r.r^

Q: ermine the torque require steady state if it is free to

A: given:

Q: agram, explain about Flexil

A: Flexible Manufacturing System; A flexible manufacturing system (FMS) is a manufacturing process that…

Q: Solve the problem sh

A:

Q: Find the ratio for the tool P and Q

A: Given data,  Two tools P and Q have signatures       50-50-60-60-80-300-0 and…

Q: A body of 5.89N is lifted by two strings, making angles of 20 and 35° with the vertical. Compute the…

A:

Q: = for the System s hown below Calculate the Pressune Point A.

A:

Q: deal gas exerts

A: 6) ANSWER= 86.064psig

Q: (a) A body of weight 45 N is placed on a rough horizontal plane. To just move the body on the…

A:

Q: Draw a circular hole of 2cm deep and give dimensions to it.

A:

Q: Determine the power required to drive compressor

A: Given data; P1=1 bar=100 KN/m2T1=25+273=298 KP3=42 bar=4200 KN/m2n=1.25m=1.2 kg/minR=287…

Q: Find the angle at which the compound rest is to be swivelled or set with the following data: a)…

A: Answer: The angle at which compound rest is to be swivelled is 7.125°.

Q: Calculate the internal force values for 0=120° Wo

A: Given: The beam with distributed loading is shown below:

Q: Find the value of Pmax if the the

A: need to find Pmax

Q: g has a diameter of de up of semicirc having reluctar

A:

Q: 4. What are the theorems of Papus and Guldinus used for?

A: It is required to find use of papus and guldinus theorem

Q: Three cables are connected at A for which cable AD is just taut.

A:

Q: figure below. Decide by calculation whether Over Take Car A after 2 minutes.

A:

Q: Calculate the resultant force on the screw eye. Note the upper part of the rope is horizantal.

A:

Q: (a) A body of weight 45 N is placed on a rough horizontal plane. To just move the body on the…

A: Here 2 question a). and b). are different questions. As per honor code and answering guidelines I…

Q: analytical and graphical solution of the forces

A: Given BA=5.755kN strut, this means it is -ve CA=4.317kN tie

Q: Problem -1 A tank containing of 50 Kg of water saturated liquid at constant temperature is 90°C.…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Q3: Calculate the applied force to move the process

A:

Q: A 12 B A riveter, as shown in Fig. 7.42, is operated by a piston Facting through the links EB, AB…

A: Given: Input force on the piston F=2.2kNEfficiency of the mechanism η=72%BC=2AB

Q: Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pr

A: Given Data⇒ Cast iron cylinder Diameter of cylinder(d)=250 mm Pressure (P)=0.7 Nmm2 Maximum tensile…

Q: = direction is (Ris fuleru

A:

Q: "his shaft is subje - 10,000 in-lb., fom and F - 20,000 lb approsch, deter

A:

Q: Where to put marker for maximum steady state force. It is F-t graph.

A: Concept: Steady state means the graph line looks almost constant with zero slope and it is parallel…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.