Mr. X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat the water. What is the quantity of alum required to treat 14 million liters of water per day at a treatment plant. Also determine the amount of carbon dioxide gas produced per liter of water during treatment. BIU GGG :H E T A

Mr. X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat the water. What is the quantity of alum required to treat 14 million liters of water per day at a treatment plant. Also determine the amount of carbon dioxide gas produced per liter of water during treatment. BIU GGG :H E T A

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

In standardization, 10.00 mL of Naz C2 04 solution required 39.17 mL of KMN04. Find the molarity of KMNO,. The unknown required 14.44 mL of MnO,. Find Ca in the urine. (Answer: 1.086 x 10 M, 7.840 x 10 M)
Q.2(a) What will be the influence of using more alkaline/acidic water in boilers? Discuss the type of corrosion resulting from it and their method of prevention. (b) Calculate the hardness in a given hard water sample having the following data. 50 ml of standard hard water containing 1 mg of CaCO3 per ml consumed. 50 ml of standard hard water consumed 25 ml EDTA using eriochrome black T as indicator. 50 ml water sample consumed 40 ml EDTA using the same indicator. 50 ml water sample after boiling consumed 25 ml of EDTA using the same indicator. (c) Discuss the problems of boilers which can be arises due to use of high concentration of alkaline substance along with their prevention and disadvantages.
3. Table below shows the concentration of dissolve oxygen for a BOD test, diluted by 100. Time (days) Diluted sample DO (mg/L) 7.95 1 3.75 2 3.45 2.75 2.15 1.8 i. Determine BOD5 Given the deoxygenation rate coefficient of 0.15 day-1, determine the ultimate BOD ii. iii. Based on answer from (i), identify class of the water sample based on INWQS guideline and propose suitable usage the water.
Available chlorine in bleaching powder solution is 0.5mg/ml. To obtain a chlorine dose of 0.1 mg/1 in a 300 ml water sample, the amount of bleaching powder solution to be added is ml.
A Pump & Treat water treatment system at a contaminated site is designed to treat 5 m3/d of ground water in a reactor designed as a well mixed system. The effluent must meet quality standards of 25 mg/L of Iron. The treatment reactor’s 20 m3 volume is believed to be insufficient to achieve the standard. The ground water has an iron concentration of 100 mg/L and the treatment reactor has a kinetic constant of 0.5 d-1. – Confirm that the treatment system will NOT meet the effluent quality standards. – If not modify the design by adding a PFR system (using same treatment process and kinetics), what volume should the PFR addition be?
The concentration of SO2 measured at an air monitoring station was 8 mg/m3 at T=30 oC and 1 atm pressure. Does this value exceed the 1-hour, primary NAAQS for SO2
A sample is diluted to perHorm test 295 mL distilled water are added to 5mL sample to fill 300ML BOD bottle. Inifial dissolved oxygen concentration is 7.9 mg/L in the bottle After mcubating 5 days, dissal ved oxygen carcentvation 1s 45 mg/L- Determine 5-day BOD OF the wastewae- Deoryge nation rate Constant, k, is C.013 day- Evaluate ultimate BOD Of the wastewCHer.
1. A CM reactor receives influent containing 10 mg/L of tracer dye for 2 hours. The tracer addition is terminated but the flowrate of water is maintained. The volume of the reactor is 10 L and the flowrate is 2 L/hr. What is the concentration of tracer in the reactor 1 hr after the dye addition is terminated? The reactor had an initial concentration of tracer of 1 mg/L when the tracer addition commenced.
What is the pH of a solution made by dissolving 3.71 grams of calcium fluoride in enough water to make 450 mL of solution? The Ka for HF is 6.8x10-4.
EA two-stage distiller system is used to remove TDS from sea water as shown in the figure. The concentration of IDS (mg/) in the brine leaving Stage 2 distiller is: Stea Stage 2 Q4 MGD Brine Sea water Q 13 MGD TDS-38000 Frosh water Q11 MGD TDS- 70 mg Heat Heat (ii) 123,308 ad from the giyen information (iv) 246,615 (vi) none of the above (i) 332,615 (ii) 170,615
Liquid alum is delivered to a water treatment plant which contains 642.3 milligrams of alum per milliliter of liquid solution. Jar tests indicate that the best alum dose is 8 mg/L. Determine the setting on the liquid alum chemical feeder in milliliters per minute when the flow is 2.2 MGD.
(a) (ii) Following chemical species were reported for water sample from a well. Concentration (milli equivalent)/L 15 15 05 30 12 18 8.8 Species Chloride (CL) Sulphate (SO2-) Carbonate (CO2) Bicarbonte (HCO3) Calcium (Ca²+) Magnesium (Mg2+) pH Find (i) The total hardness (in mg/L) as CaCO3 (ii) Alkalinity present in the water (in mg/L) as CaCO3.