Motorized moving platform is lifting a car with some acceleration. If the combined weight of the lift platform and car is 2800kg, and the motorized lift weight is 200000kg, determine the maximum acceleration of the platform before tipping occurs. Weight of the platform a=2.1m, b 4m, c = 4.2m, d = 3m Vertical lift platform center of gravity (car) a C 00 center of gravity (lift)

Motorized moving platform is lifting a car with some acceleration. If the combined weight of the lift platform and car is 2800kg, and the motorized lift weight is 200000kg, determine the maximum acceleration of the platform before tipping occurs. Weight of the platform a=2.1m, b 4m, c = 4.2m, d = 3m Vertical lift platform center of gravity (car) a C 00 center of gravity (lift)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.41P: The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking...

See similar textbooks

Similar questions

The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate motion if =35.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.
The figure models the handle of the water cock described in Prob. 4.9. Draw the FBD of the handle, neglecting its weight. Count the unknowns.
The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
The 400-kg drum is held by tongs of negligible mass. Determine the magnitude of the contact force between the drum and the tongs at D.
A 6-m long ladder has a mass of 13 kg., and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal. How far up along the ladder can a 78-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B.
find the mass of the automobile by treating it as an undamped single-degree-of-freedom system?(Need handwritten solution only please otherwise downvote)
A Center Raft A person is standing at one end of a uniform raft of length L that is floating motionless on water, as shown above. The center of mass of the person-raft system is a distance d'from the center of the raft. The person then walks to the other end of the raft. If friction between the raft and the water is negligible, how far does the raft nove relative to the water? L/2 B L C d/2 Ⓡ O d Center of Mass of System 2d in
A 6-m long ladder has a mass of 16 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal.How far up along the ladder can a 79-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B.
The input piston and output plunger of a hydraulic car lift at the same level, as shown in the drawing. The cross-sectional area of the input piston is 12cm^2, while that of the output plunger is 1200cm^2. The force F1 is applied to the input piston had a magnitude of 150 N. What is the weight W of the car? Neglect the weight of the piston and plunger.
Three identical steel balls, each of mass m=80kg, are placed in the cylindrical ring which rests on a horizontal surface and whose height is slightly greater than the radius of the balls. The diameter of the ring is such that the balls are virtually touching one another. A fourth identical ball is then placed on top of the three balls. Determine the force P (in N, roundoff to 2 decimal places exerted by the ring on each of the three lower balls.