Mention a question on the topic of optimization in engineering analytics, provided the question is applied?

Q: 2/5 The position of a particle in millimeters is given by s = 27 – 12t + , where t is in seconds.…

A: Given, Position as a function of time = s = ( 27 - 12 t + t2 ) mm   Velocity function can be found…

Q: The vertical component of support reaction at B ( in N) is 400 N/m 3 m -3 m

A:

Q: B/The three components of velocity in the flow field are given below. Determine an expression for…

A: u= x2 + y2 + z2v= xy + yz + z2w= -3xz - z22 + 4

Q: What horsepower is required to isothermally compress 800 ft3of air per minute from 14.7 psia to 120…

A:

Q: 9.6 kN 10.5 kN 10.5 kN 5.7 kN D 5.7 kN F 2.4 m A E 3.8 m 3.2 m 3.2 m 3.8 m - PA

A: find the force in each members.

Q: Find the moment of resistance of the section. The permissible stresses are 10 N/mm2 in tension and…

A:

Q: Using the performance curves below, For a prototype that is 10 times larger than the model and…

A: Solution: Given Data (From the performance curves): CH=5.2CP=0.69CQ=0.12N=600 rpm=10 rps   Note:…

Q: 23.) A Carnot engine produces 61,768 hp of power while operating between temperature limits of…

A:

Q: The vertical component of support reaction at B ( in N) is 400 N/m -3 m 3 m-

A:

Q: 9- Crude oils with a large volume of issolved gases are less dense, light in eight, and have high…

A: Yes, it is true.

Q: The evaporator is device used in the high pressure side of a refrigeration Cyctem

A: This question is based on the concept of evaporator in the refrigeration on system.

Q: Determine the distance (in m) from Point O where the resultant acts 260 N 200 N 2 m 2 m 2 m

A:

Q: 2/4 The velocity of a particle along the s-axis is given by v = 5s32, where s is in millimeters and…

A:

Q: A minivan is pulled by a tow truck at 60 kph. The boxlike van is 20m long, 6m high, and 3.75m wide.…

A: Given   Velocity, v = 60 km/h = 16.67 m/s    Length, L = 20 m       Density =  0.0023 kg/m3…

Q: Q3/ For the figure shown below, compute the centroid of the figure. 6m 4.5 m 3m

A:

Q: Assuming a minimum design factor = 2.00, Design the bolted cover of pressure vessel; determine the…

A:

Q: A hollow steel shaft with an outside diameter of 41 mm and a wall thickness of 9 mm is subjected to…

A:

Q: Find the amplitude of the 1st, 2nd and 3zrd harmonics. Sawtooth Wave 3. 0.05 0.1 0.15 0.2 Time (sec)

A: Given data: wave form : sawtooth amplitude at fundamental frequency = 3

Q: Q) A 6-mm cliameter Sphere is droped into Loaler. The weight of the ball and bouncy force exered on…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: What is the beam deflection at point C when P = 10 kN, L = 1.5 m, E = 200 GPa, and I = 20E6 4? mm

A:

Q: Find the resultant couple moment (in N.M) at point O. 500 N 300 N 200 N m 2 m 2 m

A:

Q: 5 KN SKN 45 E 3 m Bc : CD %3D

A:

Q: The interior of a refrigerator has a surface area of 6.2 m2. It is insulated by a 2 cm thick…

A: Answer: The power required to run the compressor: 176.91 W

Q: Q1/ Find the polar moment of inertia of the shaded area. у-ахis -100 mm 1 x2 100 %3D -30 х-аxis ww…

A: When an amount of force act on an object, then it tends to rotate the object about a point, that…

Q: Explain why we use temperatures at high altitudes? | air-conditioning systems f. air planes despite…

A: Given Steam jet water vapor refrigeration Thermoelectric system  Vortex tube refrigeration  Airplane…

Q: Which among the following is the conect range ốf value for the icluded angle of aVbelt? O 10° to 20°…

A:

Q: Engineering Drawing: Dimensions

A:

Q: The wood beam shown is reinforced on the bottom with a steel strip. Determine the maximum bending…

A: Answer: The maximum bending moment that can be carried safely by the beam: 25.8 kN•m

Q: The amount of heat is equal to the done work according to the: * conservation of energy law…

A: According to the law of conservation of energy,The amount of heat is equal to the work done. From…

Q: F8-6. Determine the state of stress at point A on the cross section of the pipe assembly at section…

A: Find  State of stress at A

Q: Mass of car: 1400 kg B H m- C -2 m- + 1.5 r Mass of trailer: 800 kg Braking force at C (uc= 0.40) is…

A:

Q: Show by calculation that heat is not a state function. Use the first law of thermodynamics and…

A:

Q: 6.4 (WILEYa The three components of velocity in a flow field are given by u = x + y + z? v = xy + yz…

A:

Q: 3- Why is stress not directly measurable? 4- Is there any deviation between experimental and…

A:

Q: e numerical value for the ideal mechanical advantage of a bicycle with 10 teeth on e effort gear and…

A: Solution is attached below

Q: can you please provide the solution for the answer in Reaction Ay?

A:

Q: QUESTION 2 A new induced raft cooling tower is circulating 120 000 L/h of water that is cooled from…

A:

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

A:

Q: 3/detarmine the standrd area of a lshaff having diameter Cd) of Clo mn) with (o%.) accuracy and…

A: Surface area,A=π/4*d^2*l Error in Area,∆A/A*100=2*∆d/d*100+∆l/l*100 Total error in Area=2*1+2=2+2=4%

Q: e initial temperature and pressure of a 250 mm square Diesel engine is 1 bar and 310 K. If fuel…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subpartsfor…

Q: 5. Calculate the necessary draft angle for a reinforcement rib located behind a 6mm wall thickness…

A: The draft is basically an angle which is proveded to the pattern which we want to cast by using the…

Q: An ideal multi pressure refrigeration system consists of 57 tons HP Evaporator at 9°C and 63 tons LP…

A: Given that, HP Evaporator, Qhe=57 tons, The=9 °CLP Evaporator, Qle=63 tons, Tle=-26 °C,Condenser…

Q: atm. For which case do you think the energy required will be greater? Why?

A: Here we need to determine In which case Energy required will be greater.

Q: Find the resultant couple moment (in N.M) at point O. 500 N 300 N 200 N m 2 m 2 m

A:

Q: Q3) The damped vibration record of a spring-mass-dashpot system shows the following data. Amplitude…

A: When an object is disturbed from its initial equilibrium position then it tries to regain its…

Q: beam shown in Fig. 9-22. Calculate the stress at point B of the cantilever

A:

Q: How Fig (1-11)- The thin righld rod is pinned ut polnt A to a negligible mas roller, which rols on a…

A: Degree of freedom is equal to the number of independent variables in the system in order to define…

Q: answer d and e

A:

Q: a) The principal stresses for the given stress tensors. b) The directions of principal stresses. Г18…

A: For solution refer below images.

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.