A shunt generator supplies a 31kW load at 200Vthrough cables of resistance, R = 108mN. If thefield winding resistance, Rf =540 and the armatureresistance, Ra =56m2.Determine the following below:The terminal voltage is,The e.m.f. generated in the armature is,

Answered: Image /qna-images/answer/ba9fd926-368b-4fa4-80f2-ea89499b9e9c.jpg

Answered: A shunt generator supplies a 31kW load…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss about Generator modeling in transient stability and derive the formula for the real and reactive power supplied by it.
components of the excitation current I = 0.6 A and the secondary winding burden is purely A 300:5 CT with a normal ratio K = 60, magnetizing current = 1 A and loss resistive. Answer the following: 1) the actual transformation ratio K = K-K K 2) the CT ratio error 3) the ratio correction factor RCF is... 4) the phase angle error 1).. 2)... 3) them: K = K+ 1) the proper CT ratio I:1 is.. 2) The proper PT ratio V:1 is * 100% 8 = tan-¹ (m) KI, is A three phase 132 kV(₁) transmission system supplying a maximum load of 100 MVA and 0.8 pf lagging. Select the proper CT ratio (1:1) and PT ratio (V:1), where (I) could be 50, 100, 150, 200, 250, 300, 400, 450, 500, 600, 800, 900, 1000, or 1200, and line-to-neutral voltage provides 110 volts on the relay side I I, is.. is.. The resistance of the arc can be increased by several methods mention three of ) select the proper answer for the following: 1) The main processes that have the responsibility of arc initiation in the switching of the high…
What are the conditions in paralleling of these DC Generators:a. Shuntb. Seriesc. Compound
Describe how duty cycleis generated by saw-tooth and sinusoidal modulating signal and compare their performance.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Discussion:- 1. What do you understand by "armature- reaction"? Discuss the effect of armature reaction in an alternator when it is loaded with resistive, inductive and capacitive loads. 2. Give the value of voltage regulation for different power factors at full load current and interpret their values.
A shunt generator supplies a 34kW load at 225V through cables of resistance, R = 126m2. If the field winding resistance, Rf =680 and the armature resistance, Ra =42m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is, A 4 pole generator with wave wound armature has 50 slots each having 28 conductors. The flux per pole is 0.01 Wb. (i) At what speed must the armature rotate to give an induced EMF of 235V is, (ii) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
Define electronegative gases and Compare between SF6 and 02 Insulator? Explain the different schemes for cascade connection of transformers for producing very high ac voltages?
. Two dc shunt generators A and B are rated at 100 and 150 kW at 110 V respectively, Their external load characteristics may be considered as straight line. The voltage drop In the terminal voltage from no-load to full-load Is 10 V for A and 20 V ſor B. Determine the operating voltage when these generators are operated in parallel to supply a load of 220 kW.
c) What are fol d) Explain the principle of Merz prize system of protection used for power transformers. What are the limitations of thus scheme and long they are overcom. OR
vii. When two magnetic circuits are coupled..... the coupling coefficient is expressed by (a) K=M\ VL1 L2 viii. Impedance matching means (a) Transfer power to the load (c) Maximum power transfer to the load. (b) k= MIM2 (c) K= LIL2 (b) Minimum power transfer to the load
- An 8-pole wave -wound d.c generator with output current is 200 A and has ATc/pole = 2600 AT and ATd /pole= 400 AT. Find the number of conductor.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

A shunt generator supplies a 31kW load at 200V through cables of resistance, R = 108mN. If the field winding resistance, Rf =540 and the armature resistance, Ra =56m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,