M h B For the given system; a) Draw bending moment and shear force diagrams. b) Determine the most critical section. c) Show the stress distribution on this critical section. d) If allowable stresses for tension and compression are 7000 N/cm² and 12000 N/cm², respectively, determine the safety of the structure. GIVEN: {1= 80 cm, {2=40 cm, qo = 60 N/cm F= 500 N, b = 5 cm, h = 4 cm, t = 0.5 cm %3D

M h B For the given system; a) Draw bending moment and shear force diagrams. b) Determine the most critical section. c) Show the stress distribution on this critical section. d) If allowable stresses for tension and compression are 7000 N/cm² and 12000 N/cm², respectively, determine the safety of the structure. GIVEN: {1= 80 cm, {2=40 cm, qo = 60 N/cm F= 500 N, b = 5 cm, h = 4 cm, t = 0.5 cm %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A.) It is the boundary condition for fixed support Choices: Both choices Y=0 Y’=0 Either of the choices B.) It is a type of simple stress acting parallel to an area Choices: Flexural stress Shear stress Axial stress Bearing stress C.) For concentric row of bolts in a coupling connection, the shear deformations in the bolts is proportional to the: Choices Modulus of rigidity Diameter of bolt circle Radial distance Number of bolts note: please help us in the word meaing sample problems thank you
D 12KN B A 10KN 28kN + + 60KN 44kN + 120cm 80cm Ост 40cm Figure 1 a) Draw a Free Body Diagram for each section of the member above. b) Determine the force acting on the section BC. c) Draw a Normal Force Diagram for the figure above. d) Calculate the stress induced in the member BC if the diameter of the rod is 55.2791mm. e) Determine the total elongation of the rod.
For the given system;a) Draw internal force diagrams and determine the most critical section.b) Show the stress distribution on this critical section and find the maximum normal stress.GIVEN: ℓ1 = 80 cm, ℓ2 = 40 cm, M = 8000 Ncm, b = 4 cm, h = 6 cm, t = 1 cm, F = 1400 N, qo = 30 N/cm .
Q1: Considering the forces acting on the bar having solid circular cross-section, and an elastic modulus of E=200 GPa ; 50 mm 20 mm 15 kN 20 kN 30 mm 12 kN a) Draw the normal force diagram of the whole bar and obtain the normal stress at each section of the bar. A B C 0.5 m 0.3 m 0.4 m b) Calculate the elongation of point A with respect to point C c) If the factor of safety of the system is foreseen as 1.75, calculate the minimum yield stress of the bar material (-
b2 h G B M. Q4) For the given system; a) Draw internal force diagrams and determine the most critical section. b) Show the stress distribution on this critical section and find the maximum normal stress. GIVEN: (1 = 50 cm, {2= 30 cm, M, = 5000 Nem, q. = 20 N/cm, bị = 4 cm, b2 = 2 cm, h = 4 cm, t= 1 cm
A) Suppose you need to design a tension test machine capable of testing specimens that have nominal ultimate stresses as high as σu = 100 ksi . How much force must the machine be capable of generating? Assume the testing specimen has the ASTM shape shown. B) If the maximum nominal strain is ϵf = 0.7 just before the test specimen fractures and the test machine operates by moving only one grip, how far must that grip be designed to travel? The total length of the deforming part of the specimen is 3 in .
Q1. If the yield stress (oy) of a material is 375MPa, determine whether yield is predicted for the stresses acting on both the elements shown below using: P₁=-215 RF 330 (a) Tresca Criterion (b) Von Mises Criterion Q = 200 Element A Note: your values for P (vertical load on Element A) should be negative (i.e. corresponding to a compressive vertical load). Element B S=90
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
A bar with varying cross section is subjected to various forces as shown below. Compute: a) Stresses in each section b) strain in each section c) total extension of the bar. Take E = 2.1x105 N/mm² 400 mm² P1=10kN A 1000 mm B 800 mm mm² P₂ P3=45KN+ 1500 mm 600 mm² 800 mm → P4-35kN
Hertz contact theory can be used to determine the stresses due to contact between two spheres, which can be used approximate frictionless contact between the patellar and femoral components of a total knee replacement. Part a) Show on a sketch how the stresses at the surface vary from the centre of contact to the edge of contact. Part b) Make a sketch of an infinitesimal element of material at the centre of contact that shows the stress components. Identify the maximum principal stress, and write an expression for the maximum shear stress. Part c) Sketch a graph that shows how the maximum contact pressure varies with load and in a sentence explain why the curve has the shape it does.
F
1. The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity for the material b) The proportional limit c) The ultimate stress d) The modulus of resilience e) If the bar has a circular cross section with an initial diameter of 10-mm and is loaded to 260-Mpa, what will be the decrease in diameter under this load? Use v= 0.25 (MPa) Show complete solution.