Johnson Electronics manufactures a power supply used in a variety of electronics products, including printers, modems, and routers. The demand for the part is 7,400 units per week. The production of the power supply requires six different manufacturing operations, each in sequence and each having the following processing times. The net available time to work is 46 hours per week, using two shifts. Operation Operation 1 Processing Time (seconds) 16 Operation 2 13 Operation 3 22 Operation 4 15 Operation 5 28 Operation 6 19 Required: 1. What is the Takt time, in seconds, for this product? (Round your final answer to the nearest whole number.) Takt time seconds per unit 2. Is the processing line properly balanced for this product? Yes ○ No

Johnson Electronics manufactures a power supply used in a variety of electronics products, including printers, modems, and routers. The demand for the part is 7,400 units per week. The production of the power supply requires six different manufacturing operations, each in sequence and each having the following processing times. The net available time to work is 46 hours per week, using two shifts. Operation Operation 1 Processing Time (seconds) 16 Operation 2 13 Operation 3 22 Operation 4 15 Operation 5 28 Operation 6 19 Required: 1. What is the Takt time, in seconds, for this product? (Round your final answer to the nearest whole number.) Takt time seconds per unit 2. Is the processing line properly balanced for this product? Yes ○ No

Name: Johnson Electronics manufactures a power supply used in a variety of
Uploaded: 2024-03-20T06:33:06.000Z
Channel: Bartleby
Description: Johnson Electronics manufactures a power supply used in a variety of electronics products, including printers, modems, and routers.The demand for the part is 7,400 units per week. The production of the power supply requires six different manufacturi

Principles of Accounting Volume 2

19th Edition

ISBN:9781947172609

Author:OpenStax

Publisher:OpenStax

Chapter6: Activity-based, Variable, And Absorption Costing

Section: Chapter Questions

Problem 1MC: Active Frame, Inc., manufactures clear and tinted sport glasses. The manufacturing of clear glasses...

See similar textbooks

Similar questions

Use the following information for Exercises 5-44 through 5-46: The following six situations at Diviney Manufacturing Inc. are independent. a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of machine time and 7.5 pounds of material. The cost per labor hour is 12, the cost per machine hour is 8, and the cost per pound of materials is 10. b. With its original design, a gear requires 8 hours of setup time. By redesigning the gear so that the number of different grooves needed is reduced by 50%, the setup time is reduced by 75%. The cost per setup hour is 50. c. A product currently requires 6 moves. By redesigning the manufacturing layout, the number of moves can be reduced from 6 to 0. The cost per move is 20. d. Inspection time for a plant is 16,000 hours per year. The cost of inspection consists of salaries of 8 inspectors, totaling 320,000. Inspection also uses supplies costing 5 per inspection hour. The company eliminated most defective components by eliminating low-quality suppliers. The number of production errors was reduced dramatically by installing a system of statistical process control. Further quality improvements were realized by redesigning the products, making them easier to manufacture. The net effect was to achieve a close to zero-defect state and eliminate the need for any inspection activity. e. Each unit of a product requires 6 components. The average number of components is 6.5 due to component failure, requiring rework and extra components. Developing relations with the right suppliers and increasing the quality of the purchased component can reduce the average number of components to 6 components per unit. The cost per component is 500. f. A plant produces 100 different electronic products. Each product requires an average of 8 components that are purchased externally. The components are different for each part. By redesigning the products, it is possible to produce the 100 products so that they all have 4 components in common. This will reduce the demand for purchasing, receiving, and paying bills. Estimated savings from the reduced demand are 900,000 per year. 5-44 Nonvalue-Added Costs Refer to the information for Diviney Manufacturing on the previous page. Required: Estimate the nonvalue-added cost for each situation.
Cozy, Inc., manufactures small and large blankets. It estimates $950,000 in overhead during the manufacturing of 360,000 small blankets and 120,000 large blankets. What is the predetermined overhead rate if a small blanket takes 2 hours of direct labor and a large blanket takes 3 hours of direct labor?
Cozy, Inc., manufactures small and large blankets. It estimates $350,000 in overhead during the manufacturing of 75,000 small blankets and 25,000 large blankets. What is the predetermined overhead rate if a small blanket takes 1 machine hour and a large blanket takes 2 machine hours?
Use the following information for Exercises 5-44 through 5-46: The following six situations at Diviney Manufacturing Inc. are independent. a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of machine time and 7.5 pounds of material. The cost per labor hour is 12, the cost per machine hour is 8, and the cost per pound of materials is 10. b. With its original design, a gear requires 8 hours of setup time. By redesigning the gear so that the number of different grooves needed is reduced by 50%, the setup time is reduced by 75%. The cost per setup hour is 50. c. A product currently requires 6 moves. By redesigning the manufacturing layout, the number of moves can be reduced from 6 to 0. The cost per move is 20. d. Inspection time for a plant is 16,000 hours per year. The cost of inspection consists of salaries of 8 inspectors, totaling 320,000. Inspection also uses supplies costing 5 per inspection hour. The company eliminated most defective components by eliminating low-quality suppliers. The number of production errors was reduced dramatically by installing a system of statistical process control. Further quality improvements were realized by redesigning the products, making them easier to manufacture. The net effect was to achieve a close to zero-defect state and eliminate the need for any inspection activity. e. Each unit of a product requires 6 components. The average number of components is 6.5 due to component failure, requiring rework and extra components. Developing relations with the right suppliers and increasing the quality of the purchased component can reduce the average number of components to 6 components per unit. The cost per component is 500. f. A plant produces 100 different electronic products. Each product requires an average of 8 components that are purchased externally. The components are different for each part. By redesigning the products, it is possible to produce the 100 products so that they all have 4 components in common. This will reduce the demand for purchasing, receiving, and paying bills. Estimated savings from the reduced demand are 900,000 per year. 5-45 Driver Analysis Refer to the information for Diviney Manufacturing on the previous page. Required: CONCEPTUAL CONNECTION For each situation, identify the possible root cause(s) of the activity cost (such as plant layout, process design, and product design).
Plata Company has identified the following overhead activities, costs, and activity drivers for the coming year: Plata produces two models of microwave ovens with the following activity demands: The companys normal activity is 21,000 machine hours. Calculate the total overhead cost that would be assigned to Model X using an activity-based costing system: a. 230,000 b. 240,000 c. 280,000 d. 190,000
Eyring Manufacturing produces a component used in its production of washing machines. The time to set up and produce a batch of the components is two days. The average daily usage is 800 components, and the maximum daily usage is 875 components. Required: Compute the reorder point assuming that safety stock is carried by Eyring Manufacturing. How much safety stock is carried by Eyring?
Active Frame, Inc., manufactures clear and tinted sport glasses. The manufacturing of clear glasses takes 45,000 direct labor hours and involves 1,700 parts and 115 inspections. The manufacturing of tinted glasses takes 115,000 direct labor hours and involves 1,400 parts and 450 inspections. The traditional method applies $560,000 of overhead on the basis of direct labor hours. What is the amount of overhead per direct labor hour applied to the clear glass products? A. $933.33 B. $157,500 C. $322.500 D. $402,500
Five Card Draw manufactures and sells 24,000 units of Diamonds, which retails for $180, and 27,000 units of Clubs, which retails for $190. The direct materials cost is $25 per unit of Diamonds and $30 per unit of Clubs. The labor rate is $25 per hour, and Five Card Draw estimated 180,000 direct labor hours. It takes 3 direct labor hours to manufacture Diamonds and 4 hours for Clubs. The total estimated overhead is $720,000. Five Card Draw uses the traditional allocation method based on direct labor hours. A. What is the gross profit per unit for Diamonds and Clubs? B. What is the total gross profit for the year?
Computador has a manufacturing plant in Des Moines that has the theoretical capability to produce 243,000 laptops per quarter but currently produces 91,125 units. The conversion cost per quarter is 7,290,000. There are 60,750 production hours available within the plant per quarter. In addition to the processing minutes per unit used, the production of the laptops uses 10 minutes of move time, 20 minutes of wait time, and 5 minutes of rework time. (All work is done by cell workers.) Required: 1. Compute the theoretical and actual velocities (per hour) and the theoretical and actual cycle times (minutes per unit produced). 2. Compute the ideal and actual amounts of conversion cost assigned per laptop. 3. Calculate MCE. How does MCE relate to the conversion cost per laptop?
A manufacturing cell within a value stream is structured with four processes and associated processing times (for one unit): Molding: 6 minutes Grinding: 5 minutes Polishing: 5 minutes Finishing: 4 minutes How many units can the cell produce per hour (on a continuous running basis)? a. 3 units per hour b. 12 units per hour c. 15 units per hour d. 10 units per hour
Five Card Draw manufactures and sells 10,000 units of Aces, which retails for $200, and 8,000 units of Kings, which retails for $170. The direct materials cost is $20 per unit of Aces and $15 per unit of Kings. The labor rate is $30 per hour, and Five Card Draw estimated 64000 direct labor hours. It takes 4 direct labor hours to manufacture Aces and 3 hours for Kings. The total estimated overhead is $128,000. Five Card Draw uses the traditional allocation method based on direct labor hours. A. How much is the gross profit per unit for Aces and Kings? B. What is the total gross profit for the year?
Johnson Electronics manufactures a power supply used in a variety of electronics products, including printers, modems, and routers. The demand for the part is 7,500 units per week. The production of the power supply requires six different manufacturing operations, each in sequence and each having the following processing times. The net available time to work is 52 hours per week, using two shifts. Operation Operation 1 Operation 2 Operation 3 Operation 4 Operation 5 Operation 6 Required: 1. What is the Takt time, in seconds, for this product? (Round your final answer to the nearest whole number.) Takt time Processing Time (seconds) 23 20 25 22 30 25 Yes No seconds per unit 2. Is the processing line properly balanced for this product?