Izl min=lmA ZDi Vzl=3.1V Iz2 min.=1.5mA The maximum power of each of the three zener diodes in the branch shown is ZD2 Vz2=6.2V Iz3 min.=2mA ZD3 Vz3=2.7V 500 mW. The maximum current of the branch should not be more than : O a. 256.8 mA O b. 161.3 mA O c. 80.6 mA O d. 241.9 mA O e. 185.2 mA O f. 265.8 mA g. 427.1 mA O h. 346.5 mA

Izl min=lmA ZDi Vzl=3.1V Iz2 min.=1.5mA The maximum power of each of the three zener diodes in the branch shown is ZD2 Vz2=6.2V Iz3 min.=2mA ZD3 Vz3=2.7V 500 mW. The maximum current of the branch should not be more than : O a. 256.8 mA O b. 161.3 mA O c. 80.6 mA O d. 241.9 mA O e. 185.2 mA O f. 265.8 mA g. 427.1 mA O h. 346.5 mA

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
For the circuit shown in the Figure, if the diodes are silicon diodes with Vp(on)=0.7 V, and VIN=50 sin wt V, V1 =6 V and V2 = 16 V, then the value of VouTP-p) is: R, D VaN Vout v1事 2章 Oa. 25.4 V Ob. 27.4 V Oc. 29.4 V Od. 23.4 V
Given the following circuit with VDD = 9.5 V, R = 3.2 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. VDD I a. 0 A O b. 0.002766 A c. 0.002969 A d. 2.968750 A e. 2.765625 A R N V₂
Q2. All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA ミ5k2 D2 VA VOUT 5k2 Ve DIB -2V Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. CBA indicates the numbers 035 Ve DIA (ON/OFF) D8(ON/OFF) D2(ON/OFF) VoUT (sign and numerical value) VA OV A OV B A
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
Q11) For the shown figure below .Explain the state of the given diodes .Calculate the current and the voltage through each diode. D1 Si D2- Si 1N3491 1N3491 1kQ 12V 3V 1N3491 Si D3 A- II !!!
Q-3. Draw 1-V characteristics of 5 V silicon zener diode (Vz-5V) and show its parameters V Vz, Izx. Izs, Izm on the curve. Q-4. Determine the range of Road (Rmin, Rmax) that will maintain Vz at 5 volts for the circuit given below. Rs m 1.0kg V1 40 V Pzm=150mw
Figure Q2(a) shows the characteristic curve of a Zener diode. Analyse the characteristic curve to identify the approximate minimum Zener current Izk(min) and the approximate Zener voltage, Vz at IZK. -10 -9 -8 -7 -6 -5 -2 -1 Vz (V) + 1 3 4 6 7 8 Iz (mA) Figure Q2(a) Analyse the circuit in Figure Q2(b) to identify the minimum input voltage required to keep the diode in Zener region based on the values of the minimum Zener current and the approximated Zener voltage found in Question 2(a). R 1k2 VIN Figure Q2(b)
Q2:- Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop. +5 V +15 V -10 V (12 Marks) R DI +5 VoK D +5 VoK DI -5 VoH -5 Vo4 D2 D2 D2 +5 VoH D3 +5 Vo4 D3 -10 VoK D4 V. -5 Vo K (a) (b)