is: The Fourier Series of the load (output) voltage waveform of a certain rectifier supplying a pure resistive load of 10 Ohm from a 240 V, 50 Hz sinusoidal supply., is given by the relationship: 2V 2V cos neat where Fu is the peak value of the supply sinusoidal voltage. The Ripple Factor of the load current is: 634% 48.3 % 121 %

is: The Fourier Series of the load (output) voltage waveform of a certain rectifier supplying a pure resistive load of 10 Ohm from a 240 V, 50 Hz sinusoidal supply., is given by the relationship: 2V 2V cos neat where Fu is the peak value of the supply sinusoidal voltage. The Ripple Factor of the load current is: 634% 48.3 % 121 %

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The single phase half-wave uncontrolled rectifier has a freewheeling diode and a ripple free averageload current of 20A (high inductance). The source is 220V 50Hz.a. Draw the waveforms for the currents in the rectifying diode and freewheeling diodeb. Express the source current in Fourier series and draw the first five components andtheir sum.c. Determine the input PF and HF (THD) of the source current at the rectifier input
Vpk wt 2n 3n given the figure above, derive the formula for the root mean square (rms) value for the output waveform
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
For the waveform shown, determine: (a) Peak to Peak value (b) Peak value () RMS value (d) Frequency. If volts/div is 3V/div and Time/div is 25ms/div (No need to show the calculations)
Provide your complete solution and formula. Sample Problem: [EE Board April 2003 ] An alternating current of rectangular wave shape has amplitude of 10 and a frequency of one (1). What is the RMS current?
Q.B1 For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 50 ms/cm and the 'volts/cm' switch is on 5 V/cm. Calculate (a) the periodic time, (b) the peak voltage, (c) the time taken to complete half cycle. The periodic time is = The peak voltage is = The time taken to complete half cycle
(P-06) Diode FullWave (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -Please answer without abbreviation. Thank you.
If the input voltage for the given circuit below is 220 V at 60 Hz the load resistance (RL) is 560n and the average output voltage is 30 V. Assume the diodes to be germanium diodes. Determine the turns ratio of the transformer used. If a capacitor of 120 pF is connected parallel to the load resistor (RL), Determine the ripple factor. DI D2 V D3 D4 RL a. The turns ratio of transformer (Npri/Nsec) is b. The Ripple factor is eeleer
AC POWER ANALYSISFor the following waveforms, determine the average, effective, peak factor and form factor.Also show tabular results for the Characterization of Sinusoidal and Non-sinusoidal Waveforms. A.) Full wave Rectified Wave having a maximum value of Em.B.) Half wave Rectified Wave having a maximum value of Em.
For a full-wave rectified signal the dc voltage of 0.636VM. The rms value of the ac component of the output signal is 0.308Vm. Calculate the percentage ripple of a full-wave rectified signal.
For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 5 ms/cm and the 'volts/cm' switch is on 2 V/cm. Calculate (a) the periodic time, (b) the peak to peak voltage, (c) the maximum voltage, (d) the time taken to complete half cycle The periodic time The peak to peak voltage The maximum voltage The time taken to complete half cycle